Leonard TM-2020A страница 5 Скачать руководство пользователя

Страница: 5 / 9

THERMOMETER

HEAT

TRAP

SUPPLY

COLD

SOURCE

WATER

HOT

HIGH TEMPERATURE

SUPPLY

BY-PASS (FULL LINE SIZE)

HIGH TEMPERATURE RETURN

WATER FIXTURES

CIRCULATOR

DOMESTIC TEMPERED

VALVE #2

VALVE #1

(OPTIONAL)

AQUASTAT

(OPTIONAL)

METHOD #4
CIRCULATED FLOWS BETWEEN

8-25 GPM

PROCEDURE TO BALANCE SYSTEM:

1. MAKE SURE NO WATER IS BEING DRAWN. OPEN VALVE #1 AND VALVE #2 APPROXIMATELY ½ WAY AND START

CIRCULATOR.

2. OBSERVE TEMPERATURE UNTIL IT STABILIZERS.
3. CLOSE VALVE #1 SLIGHTLY IF TEMPERATURE IS TOO HOT, OR OPEN IT SLIGHTLY IF TEMPERATURE IS TOO COLD AND

ALLOW TEMPERATURE TO STABILIZE. REPEAT UNTIL DESIRED TEMPERATURE IS SET.

4. IF UNABLE TO REACH DESIRED TEMPERATURE OPEN VALVE #2 FULL, REPEAT STEPS 2 AND 3.

THERMOMETER

HEAT

TRAP

SUPPLY

COLD

SOURCE

WATER

HOT

HIGH TEMPERATURE

SUPPLY

BY-PASS (FULL LINE SIZE)

HIGH TEMPERATURE RETURN

WATER FIXTURES

CIRCULATOR

DOMESTIC TEMPERED

VALVE #1

VALVE #2

(OPTIONAL)

AQUASTAT

(OPTIONAL)

METHOD #5
CIRCULATED FLOWS GREATER

THAN 25 GPM

PROCEDURE TO BALANCE SYSTEM:

1. MAKE SURE NO WATER IS BEING DRAWN. OPEN VALVE #1 AND VALVE #2 APPROXIMATELY ½ WAY AND START

CIRCULATOR.

2. OBSERVE TEMPERATURE UNTIL IT STABILIZERS.
3. CLOSE VALVE #1 SLIGHTLY IF TEMPERATURE IS TOO HOT, OR OPEN IT SLIGHTLY IF TEMPERATURE IS TOO COLD AND

ALLOW TEMPERATURE TO STABILIZE. REPEAT UNTIL DESIRED TEMPERATURE IS SET.

4. IF UNABLE TO REACH DESIRED TEMPERATURE OPEN VALVE #2 FULL, REPEAT STEPS 2 AND 3.

Содержание TM-2020A










Результаты поиска

Содержание TM-2020A

Отзывы:

Похожие инструкции для TM-2020A

Бренды по названию

Популярные бренды

Leonard TM-2020A, Сервис настройки установки

Результаты поиска

Содержание TM-2020A

Отзывы:

Похожие инструкции для TM-2020A

Бренды по названию

Популярные бренды