Lenze ESMD Series, Руководство пользователя

Страница: 7 / 8

0 Not active
0 9600 bps (or 9600,8,N,2 if C01= 8...11)
1 Inhibit
0 TRIP reset by LOW - signal at terminal
28 or mains switching or HIGH signal at
the digital input “TRIP reset”
0 Start after LOW-HIGH change at
terminal 28
0 None
- 7 -
smd series
Parameter Setting
c06 c06 c06 c06 c06 0.0
c20 c20
c20 c20
c20 100
c40 c40 c40 c40 c40 0.0
c42 c42
c42 c42
c42 1
c61 c61 c61 c61 c61
c62 c62
c62 c62
c62
c63 c63 c63 c63 c63
c70 c70 c70 c70 c70 0
c71 c71 c71 c71 c71 0.0
c78 c78 c78 c78 c78
c79 c79 c79 c79 c79
L
Holding time - automatic
DC injection brake (Auto-
DCB)
I
2
t switch-off (thermal
motor monitoring)
Frequency setpoint via
keys or Modbus
Start condition (with
mains on)
Present
Last
Last but one
Configuration TRIP reset
(error reset)
Auto TRIP reset delay
Operating time counter
Mains connection time
counter
Automatic motor braking below 0.1 Hz by means of
motor DC current for the entire holding time
(afterwards: U, V, W inhibited) 999 0.0 {s}
100 30 {s}
240 0.0 {Hz}
60.0 0.0 {s}
1 Auto start if terminal 28 = HIGH
1 Auto-TRIP reset
status/error message
error message
Display
Total time in status “Start”
Display
Total time of mains = on
c08 c08 c08 c08 c08 100.0 Analog output scaling When 10 VDC is output at terminal 62, it will equal
this value (see c11) 999 0.0
2 Output frequency 2-10 VDC
1 Output frequency 0-10 VDC
c11 c11 c11 c11 c11 0 Configuration - analog
output (62)
5 Dynamic Braking
3 Load 0-10 VDC
4 Load 2-10 VDC
Code Possible Settings IMPORTANT
No. Lenze Name Selection
c17 c17 c17 c17 c17 0 Configuration - digital
output (A1) Output is energized if
0
Ready
1 Fault
2 Motor is running
3 Motor is running - CW rotation
4 Motor is running - CCW rotation
5 Output frequency = 0 Hz
6 Frequency setpoint reached
7 Threshold (C17) exceeded
8 Current limit (motor or generator mode)
reached
100% = smd rated output current
2 2400 bps (or 9600,8,E,1 if C01= 8...11)
1 4800 bps (or 9600,8,N,2 if C01= 8...11)
c25 c25 c25 c25 c25 0 LECOM baud rate
3 1200 bps (or 9600,8,O,1 if C01= 8...11)
0 Quick stop n20 n20
n20 n20 n20
0 LECOM power up state
2 Quick stop
1 Controller inhibit
n22 n22 n22 n22 n22 0 Serial time-out action
3 Trip fault “FC3”
n23 n23 n23 n23 n23 50 Serial fault time 65535 50 {ms}
Auto-TRIP reset after the time set in c71
Caution: Maximum setting is rated motor current
(see nameplate)
Does not provide full motor protection!
Only active if C01 is set properly
Display
0...999 h: format xxx
1000...9999 h: format x.xx (x1000)
10000...99999 h: format xx.x (x1000)
Use c08 to scale signal
If C01 = 8...11, Modbus serial communications is
active
Selects controller reaction to serial timeout
Sets the serial timeout length
0.0 = not active
999 = continuous brake
C99 C99
C99 C99
C99 Software version Display, format x.yz