Lenovo x3650 M4 BD 5466 Скачать руководство пользователя страница 1062

Страница: 1062 / 1222

2. Verify whether the firmware is at proper level.

3. Rerun the test.

4. If the problem remains, contact your IBM technical-support representative.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

218-906-000 : Brocade:InternalLoopbackTest Failed

A failure was detected during the Loopback test.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Rerun the test.

2. Verify whether the firmware is at proper level.

3. Rerun the test.

4. If the problem remains, contact your IBM technical-support representative.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA checkpoint panel test results

The following messages can result when you run the checkpoint panel test.

Test results for the DSA checkpoint panel test

The following messages can result when you run the DSA checkpoint panel test.

•

180-000-000 : Check-point Panel Test Passed

Check-point Panel Test Passed.

1050

Lenovo System x3650 M4 Installation and Service Guide

«
...
1060
1061
1062
1063
1064
...
»

Содержание x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды

Lenovo x3650 M4 BD 5466, Инструкция по установке и обслуживанию

Результаты поиска

Содержание x3650 M4 BD 5466

Отзывы:

Похожие инструкции для x3650 M4 BD 5466

Бренды по названию

Популярные бренды