manualshive.com logo in svg

Lenovo ThinkStation P360 Tower, Руководство по техническому обслуживанию аппаратной части

Поделиться
Скачать
Lenovo ThinkStation P360 Tower Скачать руководство пользователя страница 81

Secondary hard disk drives

Prerequisite

Before you start, read 

Generic Safety and Compliance Notices

, and print the following instructions.

Attention:

The internal storage drive is sensitive. Inappropriate handling might cause damage and 

permanent loss of data. When handling the internal storage drive, observe the following guidelines: 

•  Replace the internal storage drive only for upgrade or repair. The internal storage drive is not designed for 

frequent changes or replacement.

•  Before replacing the internal storage drive, make a backup copy of all the data that you want to keep.

•  Do not touch the contact edge of the internal storage drive. Otherwise, the internal storage drive might get 

damaged.

•  Do not apply pressure to the internal storage drive.

•  Do not make the internal storage drive subject to physical shocks or vibration. Put the internal storage 

drive on a soft material, such as cloth, to absorb physical shocks.

For access, remove these parts in order, if any: 

•  “Computer cover” on page 53

•  “Optical drive” on page 54

•  “Front bezel” on page 55

•  “Optical drive cage” on page 74

Removal steps of the 2.5-inch secondary storage drive, bracket, and cage

Chapter 7

.

Hardware removal and installation

75

Содержание ThinkStation P360 Tower





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды