Lenovo ThinkCentre M800 Скачать руководство пользователя

Страница: 138 / 178

11. Install the Wi-Fi adapter card into the PCI Express x1 slot on the system board. See “Parts on the

system board” on page 35.

Figure 84. Installing the Wi-Fi card

12. Close the card latch to secure the Wi-Fi adapter card.

Figure 85. Securing the Wi-Fi adapter card

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 147.

Replacing the Wi-Fi antenna

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

To replace the Wi-Fi antenna, refer to either of the following:

•

“Replacing the front Wi-Fi antenna” on page 130

•

“Replacing the rear Wi-Fi antenna” on page 133

Replacing the front Wi-Fi antenna

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

130

ThinkCentre M800 and M900 Hardware Maintenance Manual

Содержание ThinkCentre M800


















































































































































































Результаты поиска

Содержание ThinkCentre M800

Отзывы:

Похожие инструкции для ThinkCentre M800

Бренды по названию

Популярные бренды

Lenovo ThinkCentre M800, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkCentre M800

Отзывы:

Похожие инструкции для ThinkCentre M800

Бренды по названию

Популярные бренды