manualshive.com logo in svg

Lenovo ThinkAgile VX 4-Socket 4U Certified Node, Руководство пользователя

Узнайте все о Lenovo ThinkAgile VX 4-Socket 4U Certified Node, скачав бесплатное руководство пользователя на нашем сайте. Этот мощный продукт предназначен для удовлетворения потребностей вашего бизнеса. Получите подробную информацию о функциях и настройках, скачав руководство с {вебсайт}.

Поделиться
Скачать
background image

DCPMM contains spared internal cells to stand in for the failed ones. When the spared cells are exhausted 
to 0%, there will be an error message, and it is advised to back up data, collect service log, and contact 
Lenovo support.

There will also be a warning message when the percentage reaches 1% and a selectable percentage 
(10% by default). When this message appears, it is advised to back up data and run DCPMM diagnostics 
(see 

https://sysmgt.lenovofiles.com/help/topic/LXPM/running_diagnostics.html

). To adjust the selectable 

percentage that the warning message requires, go to 

Intel Optane DCPMMs 

➙ 

DCPMM Configuration

, 

and input the percentage.

Alternatively, change the selectable percentage with the following command in OneCLI:

onecli.exe  config  set  IntelOptaneDCPMM.PercentageRemainingThresholds  20  
--imm  USERID:[email protected]

Where 

20 

is the selectable percentage.

RAID configuration

Using a Redundant Array of Independent Disks (RAID) to store data remains one of the most common and 

cost-efficient methods to increase server's storage performance, availability, and capacity. 

RAID increases performance by allowing multiple drives to process I/O requests simultaneously. RAID can 
also prevent data loss in case of a drive failure by reconstructing (or rebuilding) the missing data from the 
failed drive using the data from the remaining drives.

RAID array (also known as RAID drive group) is a group of multiple physical drives that uses a certain 
common method to distribute data across the drives. A virtual drive (also known as virtual disk or logical 
drive) is a partition in the drive group that is made up of contiguous data segments on the drives. Virtual drive 
is presented up to the host operating system as a physical disk that can be partitioned to create OS logical 
drives or volumes.

An introduction to RAID is available at the following Lenovo Press website:

https://lenovopress.com/lp0578-lenovo-raid-introduction

Detailed information about RAID management tools and resources is available at the following Lenovo Press 
website:

https://lenovopress.com/lp0579-lenovo-raid-management-tools-and-resources

Install the operating system

Several options are available to install an operating system on the server.

• 

Lenovo XClarity Administrator

If you are managing your server using Lenovo XClarity Administrator, you can use it to deploy operating- 
system images to up to 28 managed servers concurrently. For more information about using Lenovo 
XClarity Administrator to deploy operating system images, see:

http://sysmgt.lenovofiles.com/help/topic/com.lenovo.lxca.doc/compute_node_image_deployment.html

• 

Lenovo XClarity Provisioning Manager Lite

Lenovo XClarity Provisioning Manager Lite is used to install operating system of single server. You can 
complete operating system installation by following the instructions in Lenovo XClarity Provisioning 
Manager Lite OS Installation function.

Chapter 5

.

System configuration

75

Содержание ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkAgile VX 4-Socket 4U Certified Node

H3C UniServer R6900 G5 Installation, Quick Start preview
UniServer R6900 G5
Бренд: H3C Страницы: 17
Gigabyte W131-X30 Quick Installation Manual preview
W131-X30
Бренд: Gigabyte Страницы: 2
IBM System X Series Rack Installation Instructions preview
System X Series
Бренд: IBM Страницы: 6
IBM 8672-26x Manual preview
8672-26x
Бренд: IBM Страницы: 75
Fujitsu PRIMERGY SX940 Manual preview
PRIMERGY SX940
Бренд: Fujitsu Страницы: 44
Fujitsu PRIMERGY RX900 S2 Operating Manual preview
PRIMERGY RX900 S2
Бренд: Fujitsu Страницы: 114
Fujitsu PRIMERGY RX800 S2 Options Manual preview
PRIMERGY RX800 S2
Бренд: Fujitsu Страницы: 66
Fujitsu Primergy RX600 Start Manual preview
Primergy RX600
Бренд: Fujitsu Страницы: 8
Fujitsu PRIMERGY S60 Manual preview
PRIMERGY S60
Бренд: Fujitsu Страницы: 99
Fujitsu PRIMERGY SX05 S1 User Manual preview
PRIMERGY SX05 S1
Бренд: Fujitsu Страницы: 52
Fujitsu PRIMERGY RX600 S5 Options Manual preview
PRIMERGY RX600 S5
Бренд: Fujitsu Страницы: 82
Fujitsu PRIMERGY ServerView Suite Manual preview
PRIMERGY ServerView Suite
Бренд: Fujitsu Страницы: 62
Fujitsu PRIMERGY RX800 S2 Operating Manual preview
PRIMERGY RX800 S2
Бренд: Fujitsu Страницы: 149
Fujitsu PRIMERGY RX600 S6 Operating Manual preview
PRIMERGY RX600 S6
Бренд: Fujitsu Страницы: 134
Fujitsu PRIMERGY RX600 S6 Service Supplement Manual preview
PRIMERGY RX600 S6
Бренд: Fujitsu Страницы: 62
Fujitsu Primergy RX600 S2 Operating Manual preview
Primergy RX600 S2
Бренд: Fujitsu Страницы: 121
Fujitsu PRIMERGY RX500 S7 Operating Manual preview
PRIMERGY RX500 S7
Бренд: Fujitsu Страницы: 88
Fujitsu PRIMERGY RX600 S3 User Manual preview
PRIMERGY RX600 S3
Бренд: Fujitsu Страницы: 305

Бренды по названию

Популярные бренды

Загрузить еще бренды