Lenovo ThinkAgile VX 4-Socket 4U Certified Node Скачать руководство пользователя страница 215 | Manualshive

Страница: 215 / 296

background image

7. Exit maintenance mode.

Install a RAID/HBA card (lower tray)

The lower RAID/HBA card is in the lower compute tray that is accessed from the front of the server. Connect

the three cables to the RAID/HBA card; then, connect the RAID/HBA card to the storage interposer in the

lower compute tray.

S002

CAUTION:
The power-control button on the device and the power switch on the power supply do not turn off the
electrical current supplied to the device. The device also might have more than one power cord. To
remove all electrical current from the device, ensure that all power cords are disconnected from the
power source.

Complete the following steps to install a lower RAID/HBA card:

Watch the procedure

. A video of the installation process is available:

•

•

Figure 120. Lower RAID/HBA card installation

.

Hardware replacement procedures

205

«
...
213
214
215
216
217
...
»

Содержание ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkAgile VX 4-Socket 4U Certified Node

Бренд: Omneon Страницы: 2

EKI-152X series

Бренд: Advantech Страницы: 94

Snap! Server 4000

Бренд: Quantum Страницы: 8

TVS-72XU Series

Бренд: QNAP Страницы: 53

QuantaGrid D51PH-1ULH

Бренд: QCT Страницы: 167

SC450NX - Server Platform - 0 MB RAM

Бренд: Intel Страницы: 200

Бренд: Alfresco Страницы: 49

Бренд: eNet Страницы: 7

Бренд: Promise Technology Страницы: 2

Бренд: Promise Technology Страницы: 324

Бренд: Measy Страницы: 15

Бренд: Meinberg Страницы: 4

TalkAnytime TA410

Бренд: Multitech Страницы: 209

Ethernet TV VOD-WM v4.2.1

Бренд: VBrick Systems Страницы: 38

Бренд: Avere Страницы: 52

AcquiSuite A8810

Бренд: Obvius Страницы: 28

5big - Network NAS Server

Бренд: LaCie Страницы: 5

Бренд: IBM Страницы: 244

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды