Lenovo RackSwitch G7052 Скачать руководство пользователя страница 30

Страница: 30 / 86

G7052 Installation Guide

Before Installing the G7052

Recording Important Product Information

Attention:

Product information is required in order to register your G7052, update

its firmware, place a service call, or replace the unit.

Some of the product information labels may be hidden from view once the G7052 is

installed. To prevent the need to remove the switch in order to read required product

information, locate and record the information shown on

Table 6

prior to installation.

An example of the product information labels is shown as follows:

Figure 7. Sample product labels from bottom, top, and rear of the switch

Note:

These examples are to help locate and identify the information labels. The

actual labels and information for your specific switch may differ.

The identification labels on the front, rear, and/or bottom of the G7052 contain the

Machine Type-Model (MTM) number, serial number, part number of the switch.

These labels also include the Media Access Control (MAC) address (on the rear

panel of unit) of the switch. Though helpful, the MAC address is not required for

opening a service call.

Print this page and record product information below. Keep the information in a safe

place for future reference. You will need this information when you register the

switch or open a service call with Lenovo.

For convenience, once the G7052 is installed and initialized, you can use the

show sys-info

command in the switch firmware interface to display the product

serial number and other required information. For more information, see

“Configuring Vital Product Data” on page 66

Table 6. Important product information

Product Name

RackSwitch G7052

Machine-Type Model

Serial Number

Part Number

Media Access Control (MAC)

address for switch

MAC addresses for other

components

Machine Type-Model 1611-16E
S/N 1000001

P/N: 00E6965

FRU P/N: 00D6002

(1S) Lenovo MT-Model, S/N 161116E 1000001

S/N Y010CM1AG001

Made in Malaysia Date: 12-07-17 EC L37940

16116e100001

*00E6965*
*Y010CM1aG01*

MT: 7844-590 PID: 7844AGV

SN: 06AA123

MT: 7844 590
SN: 06AA123

EID:000435

Содержание RackSwitch G7052























































































Результаты поиска

Содержание RackSwitch G7052

Отзывы:

Похожие инструкции для RackSwitch G7052

Бренды по названию

Популярные бренды

Lenovo RackSwitch G7052, Руководство по установке

Результаты поиска

Содержание RackSwitch G7052

Отзывы:

Похожие инструкции для RackSwitch G7052

Бренды по названию

Популярные бренды