Lenovo RackSwitch G7052 Скачать руководство пользователя страница 66

Страница: 66 / 86

G7052 Installation Guide

Replacing the G7052

Preparing and Returning the G7052

If replacing the G7052, remove all associated components and options according to

the instructions in this chapter. Remove and retain clips, cords, cables, modules,

caps or blanks, air-duct option (if installed), and any mounting hardware. These

items can then be reinstalled on the replacement unit.

When you remove the G7052 from the rack, record the product Machine

Type-Model (MTM) number and serial number to use for the replacement switch.

See

“Recording Important Product Information” on page 30

to locate the product

information labels on the switch or through the switch firmware interface.

To return the chassis to customer service for replacement, see

Appendix A, “Getting

Help and Technical Assistance

” on

page 75

to help you gather all the required

information that is necessary to return a component. After you remove the G7052

unit, securely pack it for shipping.

Install the replacement G7052 hardware as directed in

Chapter 3, “Installing G7052

Hardware and Options

” on

page 29

). Once the hardware is installed, configure the

Vital Product Data (VPD) on the replacement switch as shown in the following

section.

Configuring Vital Product Data

After you install the replacement G7052 hardware (the new unit), you must

configure the new unit to use the VPD of the unit which was removed (the old unit),

in order to avoid losing any licensed electronic entitlement data. The required

information consists of the old unit’s MTM and serial number, which was collected

from the old unit according to

“Recording Important Product Information” on

page 30

To configure the VPD on a new switch, complete the following steps.
1. Log in to the new G7052 as directed in

Chapter 5, “Initializing the G7052

” on

page 69

. At the Password prompt, the default password is

admin

2. Use the following CLI commands to enter the Executive configuration mode:

RS G7052>

enable

Enable privilege granted
RS G7052#

configure terminal

Enter configuration commands, one per line. End with Ctrl/Z.
RS G7052 (config)#

Содержание RackSwitch G7052























































































Результаты поиска

Содержание RackSwitch G7052

Отзывы:

Похожие инструкции для RackSwitch G7052

Бренды по названию

Популярные бренды

Lenovo RackSwitch G7052, Руководство по установке

Результаты поиска

Содержание RackSwitch G7052

Отзывы:

Похожие инструкции для RackSwitch G7052

Бренды по названию

Популярные бренды