Lenovo 6431 Скачать руководство пользователя страница 98

Страница: 98 / 284

Installing a simple-swap hard disk drive

This procedure applies only to server models that have simple-swap SATA hard disk
drives. See the

User Guide

for information about the installation sequence and

other important information.

Attention:

Simple-swap hard disk drives are not hot-swappable. Disconnect all

power from the server you remove or install a simple-swap hard disk drive.

To install a simple-swap hard disk drive, complete the following steps:

1. Touch the static-protective package that contains the drive to any unpainted

metal surface on the server; then, remove the drive from the package and place
it on a static-protective surface.

2. Align the drive assembly with the guide rails in the bay.

3. Pull the loops of the drive assembly toward each other; then, carefully slide the

drive assembly into the drive bay until it stops, and release the loops.

Note:

Do not release the loops on the drive assembly until it is completely

seated.

4. Install the lower bezel (see “Installing the lower bezel” on page 65).

5. Lock the side cover.

6. Reconnect the external cables and power cords; then, turn on the attached

devices and turn on the server.

ThinkServer TS100 Types 6431, 6432, 6433, and 6434: Hardware Maintenance Manual

Содержание 6431





























































































































































































































































































Результаты поиска

Содержание 6431

Отзывы:

Бренды по названию

Популярные бренды

Lenovo 6431, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание 6431

Отзывы:

Бренды по названию

Популярные бренды