Lenovo 6431 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 284

Lenovo 6431 Скачать руководство пользователя страница 38

be configured, and the operating system will not be able to detect it (this is
equivalent to disconnecting the device). If you disable the integrated SAS/SATA
controller and no SAS/SATA adapter is installed, the server will have no
SAS/SATA capability. If you disable the integrated Ethernet controller and no
Ethernet adapter is installed, the server will have no Ethernet capability.

This choice is on the full Configuration/Setup Utility menu only.

–

Serial Port 1

Select this choice to set up serial port 1.

–

Serial Port 2

Select this choice to set up serial port 2.

–

Parallel Port Setup

Select this choice to set up the parallel port and to adjust the parallel port
resources and features.

–

Remote Console Redirection

Select this choice to enable and configure serial remote video and keyboard
redirection.

–

Internal Floppy Support

Select this choice to disable or enable the diskette drive.

–

SATA Programming Interface

Select this choice to disable, enable, or configure the Serial ATA.

To comply with the 4690 OS requirement, this option provides a

Legacy Only

(4690)

mode that you can select from the menu. When you select the

Legacy

Only (4690)

mode, this enables the SATA 0 through SATA 3 ports for the

4690 OS.

–

Planar Ethernet

Select this choice to disable or enable the Ethernet on the system board.

–

USB Support

Select this choice to enable or disable the USB support.

–

Video

Select this choice to view the video information.

–

System MAC Addresses

Select this choice to view the MAC addresses for network devices that are
installed in the server.

v

Date and Time

Select this choice to set the date and time in the server, in 24-hour format
(

hour

:

minute

:

second

).

This choice is on the Configuration/Setup Utility menu only.

v

System Security

Select this choice to set passwords. See “Using passwords” on page 23 for more
information about passwords.

–

Administrator Password

This choice is on the full Configuration/Setup Utility menu only.

Select this choice to set or change an administrator password. An
administrator password is intended to be used by a system administrator; it
limits access to the full Configuration/Setup Utility menu. If an administrator
password is set, the full Configuration/Setup Utility menu is available only if
you type the administrator password at the password prompt.

–

Power-on Password

20

ThinkServer TS100 Types 6431, 6432, 6433, and 6434: Hardware Maintenance Manual

«
...
36
37
38
39
40
...
»

Содержание 6431





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды