Lenovo 41896HU Скачать руководство пользователя

Страница: 35 / 107

Related service information

Symptom or error

FRU or action, in sequence

0232

Extended RAM error— Extended RAM

fails at offset nnnn.

DIMM

2. System board.

0250

System battery error—System battery is

dead.

Charge the backup battery for more

than 8 hours by connecting the AC

adapter.

2. Replace the backup battery and run

BIOS Setup Utility to reset the time

and date.

0251

System CMOS checksum bad— Default

configuration used.

Charge the backup battery for more

than 8 hours by connecting the AC

adapter.

2. Replace the backup battery and run

BIOS Setup Utility to reset the time

and date.

0252

Password checksum bad - Passwords

cleared.

Reset the password by running

BIOS Setup Utility.

2. Check to see if battery may need

replacement.

0253

EFI Variable Block Data was destroyed.

Use crisis boot to recover system

bios.

2. If the same error reoccurs, contact

your service representative.

0254

System NV7 Volume checksum bad -

Default configuration used.

Load default configuration by running

BIOS Setup Utility.

0260

System timer error.

Charge the backup battery for more

than 8 hours by connecting the AC

adapter.

2. Replace the backup battery and run

BIOS Setup Utility to reset the time

and date.

3. System board.

0270

Real-time clock error.

Charge the backup battery for more

than 8 hours by connecting the AC

adapter.

2. Replace the backup battery and run

BIOS Setup Utility to reset the time

and date.

3. System board.

0271

Check date and time settings.

Verify the battery is properly inserted.

If necessary, replace the battery.

2. Set time and date using the Setup

Utility or use into operating system to

set the time and date.

0280

Previous boot incomplete—Default

configuration used.

Load “Setup Default” in BIOS Setup

Utility.

2. DIMM.
3. System board.

Содержание 41896HU












































































































Результаты поиска

Содержание 41896HU

Отзывы:

Похожие инструкции для 41896HU

Бренды по названию

Популярные бренды

Lenovo 41896HU, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание 41896HU

Отзывы:

Похожие инструкции для 41896HU

Бренды по названию

Популярные бренды