Lennox X4147 Скачать руководство пользователя страница 2

Page 2

Table of Contents

General

Page 2

. . . . . . . . . . . . . . . . . 

Shipping and Packing List

Page 2

NecessaryTools

Page 2

. . . . . . . . . . 

Thermostat Location

Page 2

. . . . . . 

Remove Existing Thermostat Page 3

Thermostat Installation

Page 4

. . . . 

Wiring Connections

Page 4

. . . . . . . 

LED Indicator

Page 5

. . . . . . . . . . . . 

Outdoor Temp. Sensor

Page 5

. . . . 

Field Wiring Diagrams

Page 6

. . . . 

Install Batteries

Page 8

. . . . . . . . . . 

Attach T’stat to Wallplate

Page 8

. . 

Set Calendar and Clock

Page 8

. . . 

Adv. Heat Pump Features

Page 9

Installer Set−Up

Page 11

. . . . . . . . . . 

System Test

Page 19

. . . . . . . . . . . . . 

Troubleshooting

Page 20

. . . . . . . . . . 

General

The Lennox X4147 programmable
touch-screen thermostat provides
control for up to three stages of heating
and two stages of cooling. The thermo-
stat may be used to control either a
conventional HVAC system which in-
cludes an outdoor condensing unit and
indoor furnace or a heat pump unit and
indoor air handler. The thermostat ter-
minal block accommodates 24V power
common from the furnace or air han-
dler. Three AAA alkaline batteries are
provided to be used as an alternate
power source or as a back−up in case
of an interruption of power.

Shipping and Packing List

Package 1 of 1 contains

1 − Assembled  thermostat  (includes

wallplate and thermostat)

1−

Bag assembly containing the fol-
lowing:

2 − Screws
2 − Wall anchors
3 − AAA alkaline batteries

1 − Installation instruction

1 − Owner’s guide

1 − Warranty certificate

Necessary Tools

S

No. 2 Phillips screwdriver

S

Standard pocket screwdriver

S

Drill

S

Drill bits (use 3/16" for drywall and
7/32" for plaster)

S

Pencil

S

Level

S

Hammer

S

Electrical tape

Thermostat Location

Install the thermostat about 5 feet
(1.5m) above the floor in an area with
good air circulation.

Do not install the thermostat where it
may be affected by the following:

S

Drafts or dead spots behind doors
and in corners.

S

Hot or cold air from ducts.

S

Radiant heat from the sun or ap-
pliances.

S

Concealed pipes or chimneys.

S

Adjacent unconditioned areas
(outside wall behind the thermo-
stat).

Содержание X4147





















Отзывы: