background image

2

Model Number Identification

V 8 LAC 01  -  2  P

Brand/Family 

V = Variable Refrigerant Flow (VRF)

Unit Type 

8 = VRF Split Heat Pumps and Heat Recovery

Unit Type 

01 = 6-10 ton Outdoor Units
02 = 12-16 ton Outdoor Units

Controls Protocol

1 = Phase 1
2 = Phase 2

3 = Phase 3

Voltage 

P = 208/230V-1 phase-60hz

Product Description

LAC = Low Ambient Cooling Kit

Application

Lennox VRF Low Ambient Cooling Kits, V8LAC01 

and V8LAC02, are to be used with VPB/VRB 6 to 

16-ton outdoor units in cold climate applications. 

 

The kits extend cooling operation range from the standard 

5°F (-15°C) down to -10°F (-23°C).

 

CAUTION

As with any mechanical equipment, contact with sharp 

sheet metal edges can result in personal injury. Take 

care while handling this equipment and wear gloves and 

protective clothing.

To ensure proper system performance and reliability, 

Lennox does not recommend operation of VRF systems 

during any phase of construction. Construction debris, 

low temperatures, harmful vapors, and operation of the 

unit with misplaced filters can damage the units. Failure 

to follow these guidelines will result in the warranty be-

ing voided.

 

IMPORTANT

The Clean Air Act of 1990 bans the intentional venting 

of refrigerant (CFC’s and HCFC’s) as of July 1, 1992. 

Approved methods of recovery, recycling or reclaiming 

must be followed. Fines and/or incarceration may be 

levied for non-compliance.

Содержание V8LAC01

















Отзывы: