7
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
reFerence
Firebox accessories / parts
cat. no.
Model no.
description
88L53
FGe
Bag of Glowing embers
(1 oz. rockwool)
80L42
FdVs
Bag of decorative
Volcanic stone
Table 8
Glowing Embers
Bag of Glowing
Embers (rockwool)
Separate into Quarter
Size (separate) Pieces
instaLL VoLcanic stone, GLoWinG
eMBers and LoGs
1.
Remove the front glass enclosure panel
(see
Removing Glass Enclosure Panels
on
Page 6
)
.
2.
Remove log set box from firebox.
Next,
remove embers and vermiculite from control
compartment.
Handle logs carefully to pre-
vent breakage.
3. install decorative volcanic stone -
Sprinkle
the decorative volcanic stone in a pleasing pat-
tern (see
Figure 6
)
. The volcanic stone should
be placed directly on top of the firebox bottom,
along the slope and to the back at the right and
left sides of the burner. Position any ceramic
fiber liners before placing the stone. Logs can
be positioned after the volcanic stone.
Figure 7
SLDVT-35 - Install the four logs as Follows
Carefully position the ceramic fiber logs over
the burner as shown in
Figure 8
. Logs should
be placed in the order shown and per the fol-
lowing instructions.
1
. Place the left front log (1) as shown. Posi-
tion it on the two left front log brackets.
2
. Place the right front log (2) as shown. Posi-
tion it on the two right front log brackets.
3
. Place the left rear log (3) as shown. Posi-
tion it on the upper and lower left rear log
brackets.
4
. Place the right rear log (4) as shown. Posi-
tion it on the right rear log bracket. Note that
the hole on the bottom of the right rear log
rests over the "Nub" on the right front log.
SLDVT-40 - Install the four logs as Follows
Carefully position the ceramic fiber logs and
twigs over the burner as shown in
Figure 9
.
Logs should be placed in the order shown and
per the following instructions.
1
. Place the ember chunk (1) over the tab on
the rear log support as shown.
2
. Place the left front log (2) as shown. Posi-
tion it on the two left front log brackets.
3
. Place the right front log (3) as shown. Posi-
tion it on the two right front log brackets.
4
. Place the left rear log (4) as shown. Position
it on the left rear log bracket.
5
. Place the right rear log (5) as shown. Posi-
tion it on the right rear log bracket. Note that
the hole on the bottom of the right rear log
rests over the "Nub" on the right front log.
WarninG: the size and position
of the log set was engineered to
give the appliance a safe, reliable
and attractive flame pattern. any
attempt to use a different log set
in the fireplace will void the war-
ranty and will result in incomplete
combustion, sooting, and poor
flame quality.
WarninG: this appliance is
not designed to burn wood. any
attempt to do so could cause irrep-
arable damage to appliance and
prove hazardous to your safety.
WarninGs: if logs are not
installed according to the log
installation instructions, flame
impingement and improper com-
bustion could occur and result in
soot and/or excessive production
of carbon monoxide (co), a color-
less, odorless, toxic gas.
WarninG: do not attempt to
install the logs until the appliance
installation has been completed,
the gas line connected and tested
for leaks and the initial burner
operation has been checked out.
Figure 6
4.
Placement of Glowing Embers -
Separate the Embers (rockwool) into pieces
about the size of a quarter (see
Figure 7)
. Keep
the pieces fluffed up, not matted. Distribute
these pieces over the surface of the burner,
as shown in
Figures 8 & 9.
Do not use more
than is necessary. Ensure that the main burner
slots remain uncovered by the ember material.
Position the embers on the small holes of the
ember bed area.
Note
:
This appliance is provided with enough
Glowing Embers for several applications, do
not use all that is in a new bag at one time.
For best glowing effect, replace the ember
material annually.
5. placement of Logs -
All logs that have locating notches or slots to
help ensure that they are properly positioned.
All top logs that rest on lower logs, do so over
notches, indents or nubs. Proper log placement
is critical to prevent sooting. Logs should be
placed in the gaps between the flame peaks and
should be positioned so they do not impinge
the flames.
Volcanic Stone
Place Volcanaic
Stone As Shown
