Lennox LI012CI-160P432-1 страница 53 Скачать руководство пользователя

Страница: 53 / 126

Installation and Maintenance

Service Manual

NO.

Malfunction
Name

Display Method of Indoor Unit

A/C status

Possible Causes

Dual-8

Code

Display

Indicator Display (during
blinking, ON 0.5s and OFF
0.5s)

Operation
Indicator

Cool
Indicator

Heating
Indicator

Refrigerant

recovery

mode

Refrigerant recovery.

The Serviceman operates it

for maintenance.

Nominal cooling mode

Indoor

ambient

temperature

sensor is

open/short

circuited

During cooling and drying

operation, indoor unit operates

while other loads will stop;

during heating operation,

the complete unit will stop

operation.

1. Loosening or bad contact of

indoor ambient temp. sensor and

mainboard terminal.

2. Components in mainboard fell

down leads short circuit.

3. Indoor ambient temp. sensor

damaged.(check with sensor

resistance value chart)

4. Mainboard damaged.

Indoor
evaporator
temperature
sensor is
open/short
circuited

AC stops operation once
reaches the setting
temperature. Cooling, drying:
internal fan motor stops
operation while other loads
stop operation; heating: AC
stop operation

1. Loosening or bad contact of

Indoor

evaporator temp. sensor and

mainboard terminal.

2. Components on the mainboard

fall

down leads short circuit.

3. Indoor evaporator temp. sensor

damaged.(check temp. sensor

value

chart for testing)

4. Mainboard damaged.

Outdoor

ambient

temperature

sensor is

open/short

circuited

During cooling and drying

operating, compressor stops

while indoor fan operates;

During heating operation,

the complete unit will stop

operation

Outdoor temperature sensor

hasnt been connected well or

is damaged. Please check it by

referring to the resistance table for

temperature sensor)

Outdoor

condenser

temperature

sensor is

open/short

circuited

During cooling and drying

operation, compressor stops

while indoor fan will operate;

During heating operation,

the complete unit will stop

operation.

Outdoor temperature sensor

hasnt been connected well or

is damaged. Please check it by

referring to the resistance table for

temperature sensor)

Outdoor

discharge

temperature

sensor is

open/short

circuited

During cooling and drying

operation, compressor will sop

after operating for about 3

mins,

while indoor fan will operate;

During heating operation, the

complete unit will stop after

operating for about 3 mins.

1.Outdoor temperature sensor

hasnt been connected well or is

damaged. Please check it by

referring to the resistance table for

temperature sensor)

2.The head of temperature sensor

hasnt been inserted into the copper

tube

Limit/

decrease

frequency

due to

overload

All loads operate normally,

while

operation frequency for

compressor is decreased

Refer to the malfunction analysis

(overload, high temperature

resistant)

Decrease

frequency

due to

overcurrent

All loads operate normally,

while

operation frequency for

compressor is decreased

The input supply voltage is too low;

System pressure is too high and

overload

Содержание LI012CI-160P432-1































































































































Результаты поиска

Содержание LI012CI-160P432-1

Отзывы:

Похожие инструкции для LI012CI-160P432-1

Бренды по названию

Популярные бренды

Lennox LI012CI-160P432-1, Руководство по обслуживанию

Результаты поиска

Содержание LI012CI-160P432-1

Отзывы:

Похожие инструкции для LI012CI-160P432-1

Бренды по названию

Популярные бренды