background image

Page 1

504,712M

*P504712M*

06/04

*2P0604*

2002 Lennox Industries Inc.

Dallas, Texas, USA

®

HP27 Outdoor Unit

HP27 outdoor units are designed for expansion valve sys-
tems only. They are not designed for RFC systems. Refer to
Lennox engineering handbook for expansion valve kits
which you must order separately.

Shipping & Packing List

1 − Assembled HP27 outdoor unit

2 − Grommets (for liquid and vapor lines)

Check equipment for shipping damage. If you find any
damage, immediately contact the last carrier.

WARNING

Improper installation, adjustment, alteration, service
or maintenance can cause property damage, person-
al injury or loss of life. Installation and service must
be performed by a qualified installer or service
agency.

IMPORTANT

The Clean Air Act of 1990 bans the intentional vent-
ing of refrigerant (CFC’s and HCFC’s) as of July 1,
1992. Approved methods of recovery, recycling or
reclaiming must be followed. Fines and/or incarcera-
tion may be levied for noncompliance.

INSTALLATION
INSTRUCTIONS

HP27 SERIES UNITS

HEAT PUMP UNITS

504,712M
06/04
Supersedes 12/03

Table of Contents

HP27 Outdoor Unit

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Shipping & Packing List

1

. . . . . . . . . . . . . . . . . . . . . . . . . 

General Information

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Unit Dimensions

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Parts Arrangement

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Setting the Unit

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Electrical

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Refrigerant Piping

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Refrigerant Metering Device

10

. . . . . . . . . . . . . . . . . . . . 

Service Valves

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Leak Testing

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Evacuation

12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Start−Up

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Manifold Gauge Set

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . 

Charging

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

System Operation

15

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Defrost System

16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Maintenance

17

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

HP27 Check Points

18

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

RETAIN THESE INSTRUCTIONS

FOR FUTURE REFERENCE

General Information

These instructions are intended as a general guide and do
not supersede local codes in any way. Consult authorities
having jurisdiction before installation.

WARNING

This product and/or the indoor unit it is matched with
may contain fiberglass wool.

Disturbing the insulation during installation, mainte-
nance, or repair will expose you to fiberglass wool
dust. Breathing this may cause lung cancer. (Fiber-
glass wool is known to the State of California to
cause cancer.)

Fiberglass wool may also cause respiratory, skin,
and eye irritation.

To reduce exposure to this substance or for further
information, consult material safety data sheets
available from address shown below, or contact your
supervisor.

Lennox Industries Inc.

P.O. Box 799900
Dallas, TX 75379−9900

Litho U.S.A.

Содержание HP27 SERIES



















Отзывы: