18
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
LENNOX HEARTH PRODUCTS • CRESTLINE™ SERIES B-VENT GAS FIREPLACES • 36"/42" LSBV MODELS • INSTALLATION INSTRUCTIONS
Figure 30
Pressure
Regulator
Remove
These
Components
Step 1.
TURN OFF THE GAS SUPPLY TO THE
APPLIANCE and disconnect power supply at
the circuit breaker. Ensure appliance is cold.
Remove the front glass door (if used) from the
appliance. Access the control compartment.
Step 2.
Carefully remove the logs. Exercise
care as not to break the logs.
Step 3.
Locate the screw securing the burner.
Remove the burner and retain the securing
screw.
Millivolt Appliances
Step 4.
SIT Systems
- Refer to
Figure 30
and
the instructions provided with the kit. Using a
Torx T20, remove and discard the three pressure
regulator mounting screws.
Remove the pressure regulator, spring, poppet,
diaphragm and bushing.
Discard all removed
components
. Ensure the rubber gasket in-
stalled on the back of the replacement pressure
regulator is properly positioned and install the
new pressure regulator using the new screws
supplied with the kit. Tighten screws to 25
in-lbs of torque.
In Canada
THE CONVERSION SHALL BE CAR-
RIED OUT IN ACCORDANCE WITH THE
REQUIREMENTS OF THE PROVINCIAL
AUTHORITIES HAVING JURISDICTION
AND IN ACCORDANCE WITH THE RE-
QUIREMENTS OF THE CAN/CGA-B149.1
INSTALLATION CODE.
LA CONVERSION DEVRA êTRE EF-
FECTUéE CONFORMéMENT AUx RE-
COMMANDATIONS DES AUTORITéS
PROVINCIALES AYANT JURIDICTION
ET CONFORMéMENT AUx ExIGENCES
DU CODE D'INSTALLATION CAN/CGA-
B149.1.
Gas conversion kits are available to adapt your
appliance from the use of one type of gas to
the use of another. These kits contain all the
necessary components needed to complete the
task including labeling that must be affixed to
ensure safe operation.
-
s
m
e
t
s
y
S
T
I
S
tl
o
v
il
li
M
s
ti
K
n
o
i
s
r
e
v
n
o
C
s
a
G
e
n
a
p
o
r
P
o
T
l
a
r
u
t
a
N
s
l
e
d
o
M
e
p
y
T
ti
n
U
.
o
N
g
o
l
a
t
a
C
8
2
6
3
-
V
B
S
L
tl
o
v
il
li
m
4
1
8
5
H
8
2
2
4
-
V
B
S
L
tl
o
v
il
li
m
4
1
8
5
H
-
s
m
e
t
s
y
S
T
I
S
tl
o
v
il
li
M
s
ti
K
n
o
i
s
r
e
v
n
o
C
s
a
G
l
a
r
u
t
a
N
o
t
e
n
a
p
o
r
P
s
l
e
d
o
M
e
p
y
T
ti
n
U
.
o
N
g
o
l
a
t
a
C
8
2
6
3
-
V
B
S
L
tl
o
v
il
li
m
2
1
8
5
H
8
2
2
4
-
V
B
S
L
tl
o
v
il
li
m
2
1
8
5
H
-
s
m
e
t
s
y
S
T
I
S
c
i
n
o
rt
c
e
l
E
s
ti
K
n
o
i
s
r
e
v
n
o
C
s
a
G
e
n
a
p
o
r
P
o
T
l
a
r
u
t
a
N
s
l
e
d
o
M
e
p
y
T
ti
n
U
.
o
N
g
o
l
a
t
a
C
8
2
6
3
-
V
B
S
L
c
i
n
o
rt
c
e
l
e
5
1
8
5
H
8
2
2
4
-
V
B
S
L
c
i
n
o
rt
c
e
l
e
5
1
8
5
H
-
s
m
e
t
s
y
S
T
I
S
c
i
n
o
rt
c
e
l
E
s
ti
K
n
o
i
s
r
e
v
n
o
C
s
a
G
l
a
r
u
t
a
N
o
t
e
n
a
p
o
r
P
s
l
e
d
o
M
e
p
y
T
ti
n
U
.
o
N
g
o
l
a
t
a
C
8
2
6
3
-
V
B
S
L
c
i
n
o
rt
c
e
l
e
3
1
8
5
H
8
2
2
4
-
V
B
S
L
c
i
n
o
rt
c
e
l
e
3
1
8
5
H
GAS CONVERSION KITS
WARNING
This conversion kit shall be installed by a qualified service agency in
accordance with the manufacturer’s instructions and all applicable codes
and requirements of the authority having jurisdiction. If the information in
these instruction is not followed exactly, a fire, explosion or production of
carbon monoxide may result causing property damage, personal injury
or loss of life. The qualified service agency is responsible for the proper
installation of this kit. The installation is not proper and complete until the
operation of the converted appliance is checked as specified in the manu-
facturer’s instructions supplied with the kit. The qualified service agency
performing this installation assumes responsibility for this conversion.
AVERTISSEMENT
Cette trousse de conversion doit être installée par un technicien agréé,
selon les instructions du fabricant et selon toutes les exigences et tous les
codes pertinents de l’autorité compétente. Assurez-vous de bien suivre
les instructions dans cette notice pour réduire au minimum le risque
d’incendie, d’explosion ou la production de monoxyde de carbone pouvant
causer des dommages matériels, des blessures ou la mort. Le tecnicien
agréé est responsable de l’installation de cette trousse. L’installation n’est
pas adéquate ni complète tant que le bon fonctionnement de l’appareil
converti n’a pas été vérifié selon les instructions du fabricant fournies avec
la trousse. Le fournisseur de service qualifié ayant réalisé l'installation
assume les responsabilités liées à la conversion.
Kit part numbers are listed here and the steps
that follow detail the conversion procedure.
