Lennox ComfortSense 8500 Series Скачать руководство пользователя страница 26

Страница: 26 / 28

Table 6. Error Codes and Reminders

Condition Issue

Display

System Action

Action to Clear / Recovery

Condition

Critical

All RTU compressors

Locked

All RTU

compressors

Locked

This error is displayed

in notification screen

and technician system

status screens.

• User will have to contact the

Service Contractor to have the

system serviced.

• Will need to check RTU state

• If the RTU recovered from the

error automatically the error will

also automatically clear.

Critical

RTU Fault State

Detected

RTU Fault

State

Detected

This error is displayed

in notification screen

and technician system

status screens.

• User will have to contact the

Service Contractor to have the

system serviced.

• Will need to check RTU state.

• If the RTU recovered from the

error automatically the error will

also automatically clear.

Reminder

Routine system

check up

Routine

system

check up

Displayed on

notification screen.

• Pressing clear button will clear

the reminder.

• Or pressing remind later on

pop-up screen will extend the

duration.

Reminder

Custom reminder 1

User

Editable

Displayed on

notification screen.

• Pressing clear button will clear

the reminder.

• Or pressing remind later on

pop-up screen will extend the

duration.

Reminder

Custom reminder 2

Содержание ComfortSense 8500 Series





























Результаты поиска

Содержание ComfortSense 8500 Series

Отзывы:

Похожие инструкции для ComfortSense 8500 Series

Бренды по названию

Популярные бренды

Lennox ComfortSense 8500 Series, Инструкция по установке и настройке

Результаты поиска

Содержание ComfortSense 8500 Series

Отзывы:

Похожие инструкции для ComfortSense 8500 Series

Бренды по названию

Популярные бренды