background image

506230−01 05/09

Page 2

IMPORTANT

Read this manual before programming the thermo-
stat.

Use this thermostat only as described in this manual.

WARNING

Always turn off power at the main power source by
switching the circuit breaker to the OFF position be-
fore installing or removing this thermostat.

All wiring must conform to local and national build-
ing and electrical codes and ordinances.

Do not switch system to cool if the outdoor tempera-
ture is below 45°F (7°C). This can damage the cool-
ing system.

ComfortSense

®

 Model L7742U Thermostat

(Catalog No. Y2081)

Description

The ComfortSense

®

 Model L7742U thermostat is an elec-

tronic 7−day universal multi-stage programmable touch
screen thermostat. It also offers enhanced capabilities
which include:

S

humidification measurement and control,

S

dew point adjustment control,

S

dehumidification measurement and control,

S

Humiditrol

®

 Enhanced Dehumidification Accessory

(EDA) capability,

S

equipment maintenance reminders,

S

worry−free memory storage feature,

S

menu−driven display.

This thermostat supports heat pump units or non−heat
pump units, with up to 4 stages of heating (dual fuel units)
and 2 stages of cooling.

Dimensions

Screen dimensions: 3−7/16" (87 mm) width x 2−9/16" (65
mm) height

Case dimensions: 5−7/8" (149 mm) width x 4−9/16" (116
mm) height x 1−1/4" (31mm) depth

Features

Compressor Short Cycle Protection

A 5−minute compressor short cycle protection timer begins
when a compressor output is de−energized. Also, if a pow-
er loss occurs, the system will go into compressor protec-
tion mode and display WAIT in the display if there is a cool-
ing or compressor heating call.

Outdoor Temperature Sensor

An outdoor temperature sensor (

X2658

) is required  for

dual fuel applications, balance points, dew point humidity
control, and with Humiditrol

®

 EDA.

In addition to measuring and displaying outdoor tempera-
ture, the outdoor sensor provides dew point adjustment
and control for all models. If used with this thermostat, the
sensor enables optimal heating equipment operation via
programmable balance points.

NOTE − The outdoor sensor uses standard thermostat wir-
ing; it may be wired using two wires of a multi−wire cable.

When the outdoor sensor is connected, the temperature
can be displayed in the information display area (see figure
2).

NOTE − For proper operation of Humiditrol

® 

EDA applica-

tions, the outdoor sensor (X2658) MUST be installed.

L" Input

L" input from the equipment is used to notify the user of an
outdoor equipment fault by displaying HVAC ERROR DE-
TECTED" when one of the following conditions exist:

S

L" terminal is activated with 24VAC and Y1 has been
activated for 5 minutes (units without LSOM, but which
use Service Light Monitor Kit), OR,

S

LSOM error signal is detected on L" input and Y1 has
been activated for 5 minutes.

NOTE − The L input is used for diagnostic information pur-
poses only, it is not intended to provide equipment protec-
tion.

Содержание ComfortSense 7000 series





























Отзывы: