background image

6. The chimney must extend at least three (3) feet (915 mm) above its 

point of contact with the roof and at least two (2) feet (610 mm) higher 
than any wall, roof or building within ten (10) feet (3m) of it (

Figure 

17

)

7. If the chimney extends higher than five (5) feet (1,500 mm) above 

its point of contact with the roof, it must be secured using a roof 
brace.

8. A rain cap must be installed on top of the chimney. Failure to install 

a rain cap may cause corrosion problems.

9. Cut and frame square holes in all floors, ceilings, and roof that the 

chimney will go through to provide a 2” (50 mm) clearance between 
the chimney and any combustible materials.  Do not fill this 2” space 
with insulation or any other combustible material.

10. Portions of the chimney which may extend through accessible spaces 

must  be  enclosed  to  avoid  contact  with  combustible  materials  or 
damage to the chimney.

11.When offsets are used, the pipe may not penetrate a ceiling or floor 

unless it is running vertical (no 30° offsets).

Figure 17

ten (10) feet

three (3) feet Min.

two (2) feet Min.

Aluminum Tape

Aluminum Tape

Fireplace

Connection

Plastic

Cover

Insulation

Flexible Pipe

Fireplace

OUTSIDE AIR CONNECTION TO THE FIREPLACE

Figure 16

THE CHIMNEY SYSTEM

Chimney Installation Notes

1. Always install an interior chimney as it will provide better performance.  

In areas with continuous temperatures below - 18° C (0° F), the use of 
an exterior chimney increases the likelihood of operating problems such 
as low draft, high rate of creosoting, and poor start-up characteristics.  
Exterior chimneys are also prone to down drafting and flow reversal.  
Installations, which are located on lower floors in the house, such as 
in a basement, in combination with outside chimney, are especially 
prone to flow reversal. If interior installation is impossible, install an 
AC chimney enclosed in an insulated chase.

2. The fireplace model Brentwood SP may be installed only with Security 

Chimneys International Ltd 6” diameter chimney systems.

3. A chimney venting a fireplace shall not vent any other appliance.

4. The minimum chimney height is 12 feet (3.7 m). In altitude, add 18” 

(450 mm) to the chimney for every 2,000 feet (600 m) above sea 
level.

5. 

All chimney installations must include at least one support.

  The 

maximum length of chimney that can be supported by the fireplace 
is 26 feet (8 m).  

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

13

Содержание BRENTWOOD SP

























Отзывы: