ENG-7
iPod Operation
1.
2.
3.
4.
5.
6.
Press SOURCE button to select “iPod” and the LCD display will show iPod Icon.
Press button to pause or play the track.
At “iPod” model, use / button to search a desired track.
During playback, long press / button to search for a desired point and then release the button. It will resume
normal playback from that point.
Press /ESC button to stop playback. Press button start playback from the first track.
Press RANDOM and RPT keys ,the function are also available in iPod mode.
Tuner Operation
Tuning a Radio Station
1.
2.
3.
4.
Press SOURCE button to select “TUNER”, the default station frequency is FM 87.5 HMZ.
Press BAND/FOLDER button to select the desired frequency band (FM or MW).
Press or button to search a desired radio station.
Long press / button 3 seconds and then release the button. It will search up / down until a radio station is
received. For fine-tuning, you can press / button repeatedly.
Selecting FM Stereo / Mono
1.
2.
3.
4.
To select stereo mode, press ST/MO button on the main unit or remote control repeatedly until “Stereo” is shown.
“Stereo” icon will be lit on when the receiving station is broadcasted in stereo.
To select mono mode, press ST/MO button again until “Mono” is shown.
When FM signal is weak and sound distortion occurs, it is better to select mono sound
Memorizing a Radio Station
Manual Store:
1.
2.
3.
4.
5.
6.
7.
Tune to a desired radio station by following steps described in Tuner Operation – Tuning a Radio Station.
Press PROG/PRESET button to enter tuning save mode. The symbol “MEM” will display. E.g. “FM 104.75 M01” with
01 flashing, where M01 is program number.
Within 10 seconds, press RPT or RANDOM button select the desired program number.
Within 10 seconds, press PROG/PRESET button to store that station in the selected memory. The “MEM” icon will be
shown and program number will stop flashing.
When using remote control, you can press / button to select a desired station number. Press PROG/PRESET
button again to confirm the setting.
If there is no key pressed within 10 seconds, it will exit tuning save mode and go back to go previous mode.
Repeat the first 5 steps to sets other stations, or change memorized stations.
There are total 20 program memories for FM and 10 program memories for MW.
Auto Store:
1.
2.
At FM mode, long press PROG/PRESET button 5 seconds to start auto store function. It will automatically search
upward and store the stations in the frequency range.
Repeat same procedure to auto stores the stations at MW mode.
Recall a Memorized Station:
1.
2.
Press the RPT or RANDOM button to select the desired station or memorized station.
The “MEM” icon will be turned on and the display will show the memorized station. E.g. “FM 104.75M: 01”.
The following default frequencies are stored in the memories when factory out.
Note:
For FM, 5 preset frequency are 87.50MHZ 90.00MHZ / 98.00MHZ / 106.00MHZ / 108.00 MHZ respectively, the rest
of 15 present frequency are 87.5MHZ.
For MW, same situation as FM status and 5 present frequency are 522KHZ / 603 KHZ / 999 KHZ / 1404KHZ / 1620KHZ,
The rest 5 present frequency are 522KHZ.
Achieve optimum reception :
1.
2.
At FM mode, extend and position the FM antenna to achieve optimum reception.
At MW mode, orientate the main unit to achieve optimum reception.
If at any time in the future you should need to dispose of this product please
note that: Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or retailer for
recycling advice. (Waste Electrical and Electronic Equipment Directive)
