Lemco micro line MLF-200 Скачать руководство пользователя страница 18

Страница: 18 / 35

DTV -

Headend

| MLF-200

Manual

The Status section provides a general view of how many programs and in what format are currently being streamed

from the device is its four outputs.

In order to setup the IP address for each program there are four tabs one for each IP output of the MLF-200.

By selecting e.g. the TS1 tab (Figure No 11) the user is able to setup the IP streamer for this specific output, following

the steps below:

1st step: Select SPTS or MPTS streaming mode.

SPTS mode: Means that each program has its own IP

MPTS mode: Means that all the programs of the current output (e.g. TS1) will be streamed in a single IP.

2nd step: For each program (in SPTS mode) or for the whole TS (in MPTS mode) the user is able to assign a

multicast IP address from 224.0.0.0 to 239.255.255.255 or a unicast IP address as well as its destination

port and protocol (UDP or RTP).

By repeating the above procedure for all four outputs of the MLF-200, the user is able to setup the IP streamer of

the device.

•

Figure No 11

Содержание micro line MLF-200
































Результаты поиска

Содержание micro line MLF-200

Отзывы:

Бренды по названию

Популярные бренды

Lemco micro line MLF-200, Руководство пользователя

Результаты поиска

Содержание micro line MLF-200

Отзывы:

Бренды по названию

Популярные бренды