manualshive.com logo in svg

LELY Splendimo 320 M, Руководство оператора, Страница: 30 / 50

Поделиться
Скачать
LELY Splendimo 320 M Скачать руководство пользователя страница 30

Replace the oil after the first 30 working hours and every 250 working hours with GX85-W140
transmission oil or equivalent.

1. Drain plug - 2. Fill plug
A. Gearbox - B. Gearbox - C. Drive Element

Figure 18. Replace the Gearbox Oil

5.2.5

Replace the Drive Element Oil

• Requirements:

• Collection container (minimum capacity: 0.5 liter)
• GX85-W140 transmission oil or equivalent

An incorrect quantity of oil will cause overheating and permanent damage to
the drive element.

1.

Move the Splendimo to the transport position (page 3-5).

2.

Put a collection container under drive element C.

3.

Clean the area around the drain plug.

4.

Remove the drain plug from drive element C and allow the oil to flow
into the collection container.

5.

Clean the drain plug.

6.

Move the Splendimo to the working position.

7.

Refill drive element C with 0.45 l of GX85-W140 transmission oil or
equivalent.

8.

Install the drain plug.

CAUTION

5-6

Maintenance

M-H026.1004EN

Содержание Splendimo 320 M



















































Отзывы:

Нет отзывов