LELY HIBISCUS 425 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 86

LELY HIBISCUS 425 Скачать руководство пользователя страница 9

4.1059.8506.0

A

1

PREFACE

Manual Contents

Welcome to this Lely manual. This manual contains the technical
information, operating instructions, maintenance procedures and
troubleshooting information for the Lely Hibiscus 425 S, 455 S and 485 S.

The information in this manual is for operators.

Study and understand this information thoroughly before you operate
the Lely Hibiscus. Failure to do so could result in damage to equipment.
Please consult your local Lely service provider if you do not understand
the information in this manual, or if you need additional information.

The instructions, figures and specifications in this manual are based on
the information that was available at the time of publication. Because
Lely continuously innovates its products, your Hibiscus may have
improvements, features or options that are not described in this manual.

All information in this manual is compiled with care. Despite all this, Lely
cannot guarantee that the manual is free of errors, in all translations.
Therefore, if you have any comments, please send your feedback to us by
e-mail ([email protected]). Mention the document number and the page
number.

Applicability

The table below shows the type numbers of the Lely Hibiscus for which
this manual is applicable.

Model designation

Model

Type number

Lely Hibiscus 425 S

Lely Hibiscus 455 S

Lely Hibiscus 485 S

4.1063.0004.1

4.1059.0014.1

4.1060.0015.1

Standard Torque Loading of Parts

All the nuts, bolts and screws used on the machine are torque tightened
to standard torque loadings applicable to the construction materials
used.

If a part has a non-standard torque loading, it is specified in the
applicable part of the manual.

«
...
7
8
9
10
11
...
»

Содержание HIBISCUS 425























































































Отзывы:

Нет отзывов