background image

Warranty

Leitner Designs warrants product to be free from defects in material and workmanship, for 

terms specified below, provided there has been normal use and proper maintenance.  All remedies 

under this warranty are limited to the repair or replacement of any item found by the factory to 

be defective within the time period specified. If you have a warranty claim, first you must call our 

factory at the number below for instructions. You must retain proof of purchase and submit 

a copy with any items returned for warranty work.  Upon completion of warranty work, if any, 

we will return the repaired or replaced item or items to you freight prepaid.  Damage to our 

products caused by accidents, Fire, vandalism, negligence, mis-installation, misuse, Acts of God, 

or by defective parts not manufactured by us, is not covered under this warranty.

THE WARRANTY TIME PERIOD IS AS FOLLOWS: (2) TWO YEARS FROM DATE OF PURCHASE.

high speed off road driving even with a light load can cause damage to the rack, accessories 

and  vehicle body. Damage caused by high speed off road driving and abuse is not covered 

under warranty.

gear pods are water resistant and not waterproof. Items that can be damaged by water should 

be stored inside there own air tight container before being placed in the gear pod. 

ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE CREATED 

HEREBY ARE LIMITED IN DURATION TO THE SAME DURATION AND SCOPE AS THE EXPRESS WRITTEN WARRANTY.  

OUR COMPANY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or 

limitation of incidental or consequential damages, so the above limitations or exclusions may not 

apply to you.  This warranty gives you specific legal rights, and you may also have other rights 

that vary from state to state.

FOR WARRANTY ISSUES WITH THIS PRODUCT PLEASE CALL LEITNER DESIGNS CUSTOMER SERVICE 

949-395-

3049 

or email us at

 [email protected]

V2 | Page 10

Содержание 00-XLMAX-01-1297











Отзывы: