Leisure Unity 2020, Руководство пользователя

Страница: 45 / 145

MOTORHOME OPERATION UNITY MOTORHOME
44
NOTE:
The jacks down LED lights must be off for Auto-
Level to function. If needed, press the ALL RETRACT
button
8
to clear and then Auto-Level should function.
3.
Retracting the Jacks:
To retract all jacks
simultaneously, press and release the All RETRACT
button
8
. All jacks will automatically retract and
return to stowed position. The pump will run in
retract mode until all of the jacks are fully stowed
(plus an additional 5 seconds) up to a maximum of
60 or 90 seconds). This is the proper method for
retracting the jacks prior to travel. You may stop
the ALL RETRACT by pressing any button on the
keypad. Jacks may be retracted in pairs by using
the UP button for each end or side for leveling
purposes however the ALL RETRACT
8
must be
used to fully stow the jacks prior to travel. The jacks
down LED’s will turn off, indicating the jacks are in
the “stowed” position.
4.
Power OFF:
Press and Release the Power Keypad
Button
6
SETTING THE NULL
The Null or “level position” has been preset from the
factory. However, if the coach is not level following an
attempt to AUTO-LEVEL, the Null is easy to reprogram.
To set the Null, push and release the POWER keypad
button
6
to engage power. The LED
10
next to the
POWER button should be lit RED when power is on.
Level the coach by deploying jacks manually (using the
DOWN keypad buttons, extend jacks until the coach is
level), or by simply parking the coach on a level site. You
do not need to have jacks deployed to set the Null. Use
a bubble level on a flat surface in the center of the coach
as a reference. Once the coach is level, turn the POWER
off at the panel. Depress and hold the AUTO-LEVEL
keypad button
7
. Continue to hold the AUTO-LEVEL
button and press then release the POWER button
6
, and listen for a series of beeps. After the panel has
beeped 5 to 6 times, release the AUTO-LEVEL button
(the keypad will continue to beep as long as the AUTO-
LEVEL button is held). The new Null has been set and
the system will maintain this setting. Press and release
the ALL RETRACT button
8
to retract the jacks to the
stowed position.
MANUAL OPERATION
1.
Power On:
Make sure your parking brake is engaged
and the ignition key is in the OFF position. Press and
release the POWER keypad button
6
to engage
power. All LED’s will come on then most will go out.
The LED
9
next to the POWER button should be
lit RED when power is on. If you attempt to extend
jacks by pressing the DOWN keypad buttons or all
jacks with the AUTO-LEVEL button, you will hear a
“deny” tone from the keypad if the ignition key and
or park brake is in the improper position.
2.
Planting the Jacks:
The jacks will be extended
in pairs Fronts or Rears or Left or Right Using the
DOWN (extend) keypad buttons, extend the jacks
until they contact the ground (this is referred to as
“planting” the jacks). As you extend each pair of
jacks the corresponding LED jack status lights will
come on to indicate jack(s) are out of the “stowed”
position. Jacks will be operated in pairs. Extend
and plant the front jacks first. Then extend
and plant the rear jacks. Only after planting
the fronts and then the rears, should side to side
corrections (leveling) be attempted. This process
will stabilize all four corners and minimize twist
prior to the leveling process. Do not manually over
extend jacks. This may cause unwanted stress on
the coach or the jacks.
3.
Leveling the Coach:
Use a bubble level on a flat
surface in the center of the coach as a reference.
Level the vehicle by using DOWN (extend) or UP
(retract) keypad buttons until the vehicle is level.
Front to rear then side to side. Jacks will be operated
in pairs. Do not attempt to lift the vehicle tires off of
the ground. Only lift (extend) enough to level and
stabilize the unit. Once level, press and release the
POWER button
6
to turn off the keypad.
NOTE:
The keypad may be left on once level has been
achieved. The keypad will enter “sleep mode” after five
minutes of inactivity.