LEHR LP 2.5S Скачать руководство пользователя страница 27

LEHR

 | 

ALL RIGHTS RESERVED 2012-2013

25

M

ANUFACTURER’S LIMITED WARRANTY

The limited warranty set forth below is given by LEHR with respect to new merchandise purchased and used 

in the United States and Canada, its possessions and territories.  LEHR warrants to the original purchaser 

that each new LEHR brand outboard is free from defects in material and workmanship and agrees to repair 

or replace under this warranty any defective product or attachment as follows from the original date of 

purchase.

3 YEARS -- Parts and Labor.

90 DAYS -- Parts and Labor, when used for income producing purposes.

30 DAYS -- Parts and Labor, if used for rental purposes.

This warranty is not transferable and does not cover damage or liability caused by improper handling, 

improper maintenance, or the use of accessories not specifically recommended by LEHR for this product. 

In addition, it does not cover any product that has been subject to misuse, neglect, negligence, or accident, 

or has been operated in any way contrary to the operating instructions specified in this operator’s manual. 

Additionally, this warranty does not cover tune-ups, spark plugs, carburetor adjustments, starter pulley or  

parts that will wear and require replacement with reasonable use during the warranty period. This warranty 

does not cover pre delivery setup or normal adjustments explained in the instruction manual.  Shipping of

parts is not the responsibility of LEHR.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS WHICH 

VARY FROM STATE TO STATE.  NO CLAIMS FOR CONSEQUENTIAL OR OTHER DAMAGES WILL BE 

ALLOWED, AND THERE ARE NO OTHER EXPRESS WARRANTIES EXCEPT THOSE EXPRESSLY 

STIPULATED HEREIN.  SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED 

WARRANTY LAST OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL 

DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU.  

LEHR does not extend any warranty for products sold or exported outside of the United States or Canada, 

its possessions and territories, except those sold through LEHR’s authorized channels of export distribution.  

The policy of LEHR is to continuously improve its products.  Therefore, LEHR reserves the right to change, 

modify, or discontinue models, designs, specifications of all products at any time without notice or obligation 

to any purchaser. 

HOW TO OBTAIN SERVICE: Warranty service is available, with proof of purchase through your local 

authorized service dealer.  To locate the dealer in your area, visit our website at www.golehr.com or call 

1-866-941-LEHR or write to 8922 Ellis Ave. LA, CA 90034.

CALIFORNIA EMISSIONS/EPA CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS  

The California Air Resources Board, the Environmental Protection Agency and LEHR, Inc. are pleased to 

explain the emissions control system

s warranty on your 2012 and later marine engine.  In California and 

the 49 states, new equipment that use marine engines must be designed, built, and equipped to meet the 

State

s stringent anti-smog standards.  LEHR, Inc. must warrant the emissions control system on your 

small off-road engine for the period listed below provided there has been no abuse, neglect or improper

maintenance of your engine.  

Your emissions control system may include parts such as: carburetors or fuel injection system, ignition 

system, catalytic converters, fuel tanks, valves, filters, clamps, connectors, and other associated 

components.  Also, included may be hoses, belts, connectors, sensors, and other emission-related 

assemblies.  

Where a warrantable condition exists, LEHR will repair your marine engine at no cost to you including 

diagnosis, parts and labor.  

MANUFACTURER

S WARRANTY COVERAGE:  

This emissions control system is warranted for ten years.  If any emissions-related part on your equipment 

is defective, the part will be repaired or replaced by LEHR.  

OWNER

S WARRANTY RESPONSIBILITIES:  

• 

As the marine engine owner, you are responsible for performance of the required maintenance listed in 

  your owner

s manual.  LEHR recommends that you retain all receipts covering maintenance on your 

  marine engine, but LEHR cannot deny warranty solely for the lack of receipts or your failure to ensure 

  the performance of all scheduled maintenance. 

• 

As the marine engine owner, you should however be aware that LEHR may deny you warranty coverage if 

  your marine engine or a part has failed due to abuse, neglect, or improper maintenance or unapproved 

  modifications. 

• 

You are responsible for presenting your marine engine to a LEHR service center as soon as the problem 

  exists.  The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.  

  If you have a question regarding your warranty coverage, you should contact LEHR at 1-866-941-LEHR.  

Содержание LP 2.5S































Отзывы: