manualshive.com logo in svg

LEHR LP 2.5S, Руководство оператора

Поделиться
Скачать
LEHR LP 2.5S Скачать руководство пользователя страница 10

LEHR

 | 

ALL RIGHTS RESERVED 2012-2013

8

OPERATION

PRE-OPERATION CHECKS

WARNING: If anything in the pre-operation check is not working properly, have it inspected and repaired

                  before operating the outboard motor.  Failure to do so could result in an accident.  

CONTROLS

• Check throttle, shift, and steering for proper operation before starting the engine. 

• The controls should work smoothly, without binding or unusual free play.

• Look for loose or damaged connections.

• Check operation of the starter and stop switches when the outboard motor is in the water.

• If the engine has not been used in some time, rev it in neutral to be sure it returns to idle before putting it 

  in gear.

ENGINE

• Check the engine and engine mounting.

• Look for loose or damaged fasteners.

• Check the propeller for damage.

CHECKING THE ENGINE OIL LEVEL

1.  Put the outboard motor in an upright position (not tilted).

2.  Check the oil level 

using the sight glas

s.  T

he oil level should cover the metal plate visible just below the 

     sight glass lens, but not so high as to touch the inside of the glass.

Recommended engine oil: 

4-stroke motor oil with a combination of  the following SAE and API oil classifications 

Engine oil type SAE:

10W-30 

Engine oil grade API: 

SE,S F, SG, SH, SJ, SL 

Engine oil quantity:

0.37USqt (0.35L)  

WARNING:

 ALL ENGINES ARE SHIPPED FROM THE FACTORY WITHOUT ENGINE OIL.  

                  ADD OIL BEFORE STARTING ENGINE.

FUEL

• Check to be sure you have plenty of fuel for your trip.

• Make sure there are no fuel leaks or propane fumes. 

FUELING INSTRUCTIONS 

WARNING: PROPANE AND ITS VAPORS ARE HIGHLY FLAMMABLE AND EXPLOSIVE!

• Stop engine before refueling.

• Do not smoke when refueling, and keep away from sparks, flames, or other sources of ignition.

• Refuel in a well-ventilated area.  

• Refuel portable fuel tanks off the boat.

USE THE CORRECT PROPANE CANISTER

Always use propane canisters or “bottles” that are the correct size. The 17 ounce or 16.4 ounce / 465g 

canisters that are approximately 3-7/8 inches (9.5 cm) in diameter are the correct canisters. 

NOTE: Do not use smaller diameter canisters as they will not latch securely to the unit and vibration may 

           cause damage to the unit and potentially result in a dangerous leak.

OIL LEVEL SIGHT GLASS

Содержание LP 2.5S































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды