lehman Trikes Raider XL 2014+ Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 38

background image

29

2014+ XL Raider

NOTE: Use appropriate tool for crimping terminals to wires. (Mac Tools– TCT1028, Blue Point–

PWC47 or H-D 41609).

1.

See Fig. 2

. Inspect crimps before installing connector. Distortion should be minimal.

2. Install trike wire harness (S001922) to body clips on underside of body.

3. Trim wiring from each OEM turn signal leaving 5 1/2” of wire.
4. Trim wiring from each taillight leaving 21” of wire. Cover wiring with heat shrink.
5.

See Fig’s. 1 & 2.

Install male terminals to turn signals and taillight wires. Install turn signal terminals

into 2 pin female connector. Install taillight terminals into 3 pin female connector. Install all wires into
main harness on body.

6. Drill hole in rear trunk floor for licence plate wiring. Route wiring through trunk floor and install female

terminals and connectors. Plug license plate light into harness. Seal harness through trunk floor with
silicone.

NOTE: 2014+ models will use an adapter harness between OEM connector and trike wire har-

ness.

•

(1) Adapter Harness 2014+ Models- S002195

BODY WIRING

Wire core crimp

Insulation crimp

Fig. 1

Fig. 2

Male terminal

Adapter Harness

«
...
27
28
29
30
31
...
»

Содержание Raider XL 2014+







































Отзывы:

Нет отзывов

Похожие инструкции для Raider XL 2014+

Бренд: X-lite Страницы: 6

Бренд: SRC Страницы: 5

Бренд: N-Com Страницы: 2

Бренд: GAS GAS Страницы: 119

MAESTRO EDGE 125 PROGRAMMED FI

Бренд: HERO Страницы: 84

Бренд: KTM Страницы: 26

ACCESORIES 2005

Бренд: Triumph Страницы: 6

Clothing Range 2006

Бренд: Triumph Страницы: 19

2007 ROCKET III

Бренд: Triumph Страницы: 20

Бренд: Triumph Страницы: 136

Speed Triple 1200 RS

Бренд: Triumph Страницы: 184

Scrambler 1200 XC

Бренд: Triumph Страницы: 640

Бренд: Shark Страницы: 56

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

TOPMASTER H0PC10ST

Бренд: Shad Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды