2
Description
Specification
Dimensions, HWD (at wall surface)
4.3” x 2.5” x 1.38” (109mm x 64mm x 35mm)
Weight, 1-gang
2.8 oz (79.4 g)
Voltage
120VAC - 60Hz / 240VAC - 50Hz
Power Consumption
50mA max.
Built-in Lighting / Surge Protection
MOV Surge suppression, High-voltage meets IEEE C62.41 (6000V and
3000A), Low-voltage meets ITU-T K.20
Cooling
None required
Backlit Buttons
3 color LEDs
Auto LED Intensity
Yes, Built-in / Standard
IR Receiver
Yes, Built-in / Standard
Status Indicator
Microprocessor Status LED
Station Equivalent
Each = 1, RadioLink Station
Ambient Operating Temperature
32 - 95°F (0 - 35°C)
Ambient Operating Humidity
5-95% non-condensing
UL, CUL and FCC Listed
Yes
Number of Gangs
Minimum Back Box Dimensions
1
2.8”H x 1.80” W x 2.5” D
2
2.8”H x 3.60” W x 2.5” D
3
2.8”H x 5.40” W x 2.5” D
4
2.8”H x 7.20” W x 2.5” D
MINIMUM BACK BOX DIMENSIONS
SPECIFICATIONS
NOTE:
UL requires one-half inch clearance between the back of the station to the back of the back box. With these dimensions
most standard back boxes that have the receiving threads for the keypad mounting screw inside the box will be adequate. Most back
boxes where the receiving threads are outside the box will be too small.
MUD RINGS
If mud rings are specified on a job it is important to test the mud rings for proper fit. Two gang mud rings, in particular, run
substantially smaller than back boxes and some brands are not large enough for the station.
The only solution is to test the fit first.
STATION SET UP IN SOFTWARE: DESIGN CENTER
In the
Project Explorer
click on
Style/Profile View
. Right click on
Keypad Styles
and select
Add Keypad Style
. In the
Object Editor
window fill in all the information for the keypad style including the EasyTouch II
Button Shape
and select SoftLine or TrimLine stations.
Remember to check or uncheck the Auto Backlight check box to enable or disable this built-in feature. Right click on button style and
setup a button style with the button color wanted. While still in
Style/Profile View
, right click on LED Styles and fill in the appropriate
information in the
Object Editor
for three-color LEDs – Red/Green/Blue with ON and OFF or multi-state colors. Change back to
Area
View
and select the room, then click on
Vantage Objects
in the
Object Explorer
and expand
Stations, RadioLink
. From the list of
stations double click on the
RadioLink Keypad Station
to place it in the room. In the
Object Editor
, name the station and make sure it
is on the correct RadioLink Bus port.
CONFIGURATION
RadioLink stations need to be configured to associate which physical station goes with the station in software. When the station is
initially powered-up, the Status LED will blink three times followed by a pause - this means the station is powered correctly but not
yet on the network.
Before
uploading the file to the Vantage system, do the following: From Design Center, click in the
Serial Number
section in the
Object Editor
and type in the serial number. Manually enter the serial number for each RadioLink station to match it with
the corresponding programming. Please note, if the serial number contains an alpha character please ignore this when typing in
serial number. The serial number of each station is located on a permanent sticker and a removable sticker on the front of the station.
Remove the sticker with the number only and place on the
Station List
report for easy reference when programming. The Main
Controller will add to its network and configure all the RadioLink stations that it has serial numbers for. This may take several minutes
depending on the number of RadioLink stations on the network. The Status LED will remain off when a station has been added to the
network and configured.
