LEGRAND Radiant Series Скачать руководство пользователя страница 24

Страница: 24 / 208

regulatory information

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

Содержание Radiant Series









































































































































































































Результаты поиска

Содержание Radiant Series

Отзывы:

Бренды по названию

Популярные бренды

LEGRAND Radiant Series, Руководство по установке

Результаты поиска

Содержание Radiant Series

Отзывы:

Бренды по названию

Популярные бренды