LEGRAND 0 489 53, Инструкция по эксплуатации

Страница: 1 / 6

1/6
CONTENTS
Miniature PIR presence detector - DALI dimming
Technical data sheet: S000104982EN-3 Updated: 03/02/2021 Created: 25/10/2018
Cat. No(s): 0 489 53
128, av. du Maréchal-de-Lattre-de-Tassigny - 87045 LIMOGES Cedex
Tel: +33(0)5 5 55 06 87 87 Fax: +33(0)5 55 06 88 88
www.legrand.com
1. USE
This miniature PIR (passive infrared) presence detector provides
automatic control of lighting loads with optional manual control.
This direct dim variant controls DALI or DSI digital dimming ballasts.
The unit detects movement using a PIR sensor and turns the load on.
When an area is no longer occupied, the load will switch off after an
adjustable timeout period.
These units come complete with accessories allowing flush mounting in
suspended ceilings or surface mounting on ceilings, or side mounting
on a luminaire.
All functionality is fully programmable using an infrared configurator.
2. TECHNICAL CHARACTERISTICS
PIR sensor
Detects movement within the unit’s detection range, allowing load
control in response to changes in occupancy.
IR receiver
Receives control and programming commands from the infrared
configurator.
Light level sensor
Measures the overall Lux level in the detection area.
LED status
The LED flashes red to indicate the following:
RJ11 connector
The sensor head has an RJ11 socket for connection to the power supply.
Power supply
This power supply has a 6 A relay. It also has connections for an auxiliary
switch that can be used to turn on the lighting manually.
CONTENTS Page
1. Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
2. Technical characteristics . . . . . . . . . . . . . . . . . 1
3. Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
4. Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
5. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
6. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
7. Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
8. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 6
9. Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
10. Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
11. Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Walk test LED active
When movement is detected
Valid setting received
2. TECHNICAL CHARACTERISTICS
(continued)
Sensor head Power supply
Dimensions See dimensions section
Weight Sensor head: 0.02 kg
Power supply: 0.08 kg
Supply 230 VAC +/-10%
Frequency 50 Hz
Number of ballasts Up to 30 dimming ballasts
Power consumption ON 923 mW, OFF 308 mW
Terminal capacity 1.5 mm²
Max. power factor
correction capacitance
40 μF
Working temperature -10°C to +30°C
5 to 95% non-condensing
Material Sensor head, side mounting bracket:
PA (polyamide) Power supply: PA
(polyamide)
Flush holder: Flame-retardant ABS
Type Class 2
Protection class IP 40
PIR lens
IR receiver
Light level sensor
Status LED