LEGRAND 0 489 17, Руководство пользователя

Страница: 6 / 8

6/8
CONTENTS
Data sheet: S000077898EN-2 Updated: 03/07/2014 Created: 10/03/2014
Cat.No(s): 0 489 17
Corridor lighting management sensor - PIR
8. SETTINGS
8.1 Detection parameters
Time delay: Length of time the load is on after detection occurs
Sensitivity:
Detection range setting
Modes:
Auto on/Auto off mode:
The lighting switches on automatically:
- When movement is detected and there is insufficient natural light.
The lighting switches off automatically:
- If no movement is detected at the end of the set time delay.
- Or if there is an adequate level of natural light (regulation function
activated).
The lighting will switch on again automatically if another movement is
detected and there is insufficient light.
Walk-through mode:
- If no movement is detected in the 20 seconds following an initial
detection, the device will cut off the load after 3 minutes.
- If another movement is detected in the 3 minutes following initial
detection, the device will cut off the load at the end of the set time
delay.
Manual on/Auto off mode:
The lighting is switched on manually and switched off automatically:
- If no movement is detected at the end of the set time delay.
After switch-off, if any movement is detected within a 30-second period,
the lighting switches on automatically (provided the Restart function
has been activated).
For any period of inactivity longer than 30 seconds, the lighting is
switched on manually.
Detection system:
Initial detection:
The load is switched on as soon as the first detection
occurs if the natural light level is below the light level threshold.
Maintain:
The load remains active if another movement is detected.
Restart: In manual mode. After switch-off, if any movement is detected
within a 30-second period, the lighting switches on automatically.
For any period of inactivity longer than 30 seconds, the lighting must be
switched on manually.
Possible in Manual on/Auto off mode only.
Alarm:
An audible signal is emitted before switch-off (1 minute before,
then 30 seconds, then 10 seconds).
Sensor parameter Default
value
Modifiable
parameters
Configuration
tools
0 882 30 0 882 35
Time delay 15 mn
3,5,10,15,20 min −
5 sec - 59 min 59s −
Sensitivity
PIR (very
high)
Low, medium,
high, very high
Modes
Auto on/Auto off
Inactive
Activate/
Deactivate
Walk-through
mode
Active
Activate/
Deactivate
Manual on/Auto
off
Inactive
Activate/
Deactivate
Detection system
Initial
PIR Non-modifiable −
Maintain
PIR Non-modifiable −
Restart
PIR
PIR and/or US, PIR,
US, Deactivate
−
Alarm
Inactive
Activate/
Deactivate
−
8. SETTINGS (continued)
8.2 Light parameters
Light level threshold:
Value at which the load switches on if the
natural light level is less than the setting.
Eye function:
Value 0 (eye on configuration tool 0 882 30) is
used to save the ambient light level in the room as the light level
threshold.
Advanced mode:
Calibration: The ambient light level measured with a luxmeter
must then be transmitted to the sensor.
Regulation: Automatic switch-off of the load 10 minutes after the
light level threshold is exceeded with an additional safety threshold
(to avoid lights switching off at the wrong moment).
Light contribution:
Quantity of additional lux brought in by the load
being switched on.
When the light contribution parameter is set to "Auto" (value 0) on
configuration tool Cat. No. 0 882 30, the sensor automatically calculates
the light contribution.
8.3 Modifying the parameters using the configuration tools
Warning:
Make sure blanking plate is removed before
modifying parameters with a configuration tool.
• 0 882 35: Simplified configuration tool
• 0 882 30: Advanced configuration tool
When the sensor receives an IR command via the configuration tool
it emits a beep to confirm the modification.
For more information about setting parameters, refer to the
configuration tool (Cat. No. 0 882 30) data sheet.
- Restore factory settings:
1st press: Short press on LEARN; the LED flashes slowly.
2nd press: Press LEARN for 10 seconds until the LED flashes quickly.
Sensor parameter Default
value
Modifiable
parameters
Configuration
tools
0 882 30 0 882 35
Light level threshold
300 lux
20, 100, 300, 500,
1000 lux
−
5 - 1275 lux −
Advanced
mode
Calibration − 0 - 99995 lux −
Regulation
Active
Activate/
Deactivate
−
Light
contribution
Auto Auto - 1275 lux −