Lectrosonics SRc-941, Инструкция по эксплуатации

Страница: 20 / 28

SRc-941 Dual Receiver
LECTROSONICS, INC.
20
TXBAT
Select the type of battery being used in the transmitter
to improve the accuracy of the battery monitor.
• 9V - Transmitter uses a 9V alkaline battery.
•
9VL
- Transmitter uses a 9V lithium battery (not
rechargeable).
• 9VT - Transmitter uses a 9V battery of any type.
Monitor its status with the timer in the LCD Main
Window. This is the best choice when using a re-
chargeable battery in the transmitter.
• AA - Transmitter uses a AA alkaline battery.
• AAL - Transmitter uses a AA lithium battery (not
rechargeable).
• AAT - Transmitter uses an alkaline, lithium or re-
chargeable AA battery. This is the best choice when
using a rechargeable battery in the transmitter.
MIXTRIM and MIXMODE
When set to the SWITCHED (dual channel mode),
special options are available to allow the audio from the
receivers to be mixed to either one or both audio output
channels.
The
MIXMODE
setting determines which audio signal
appears at which output channel:
•
MIXBOTH
mixes the audio and delivers the mix to
both output channels.
• MIXTO 1 mixes the audio and delivers the mix to
output channel 1.
• MIXTO 2 mixes the audio and delivers the mix to
output channel 2.
• DIRECT keeps the audio separated and delivers
receiver 1 audio to output channel 1, and receiver 2
audio to output channel 2.
The MIXTRIM setting applies attenuation up to 20dB in
1 dB steps to adjust the ratio of the two audio signals in
the mix. This adjustment takes effect only when a mix
mode is selected. If the MIXMODE is set to DIRECT,
the MIXTRIM option will not be available.
IMPORTANT: The output level of each receiver
is adjusted with the LEVEL setup screen, which
is hardware-based, so it affects the output level
regardless of which mix mode is selected. MIXTRIM
then applies attenuation to that level setting resulting in
the final level delivered to the output channel. It is good
practice to set the output LEVEL of both receivers
to the same value when using a mix mode.
When a MIXMODE is selected, each audio signal is au-
tomatically attenuated by 6 dB prior to the mixing. This
is done to avoid overload and potential distortion since
mixing increases the level by 6 dB.
TONE
The TONE setup screen enables an audio test tone at
the receiver output for precise level matching with other
equipment. The first screen prompts you to press the
UP or DOWN button to enable the tone at the receiver
output. Press MENU/SEL to toggle between receivers.
The first screen prompts you to
press the UP or DOWN button to
start the tone.
RECEIVER 2
TONE?
00 +05
Once the UP or DOWN button is pressed, a 1 kHz tone
is enabled, and its level can be adjusted with additional
presses on the UP or DOWN buttons.
T
he level set here will be retained in the regular operat-
ing mode. It will supersede the setting made in the
LEVEL setup screen.
The test tone has 1% distortion
and is intended for confirmation of output levels only. To
stop the tone and exit the test tone screen, press the
BACK button.
Front Panel Shortcuts
A convenient shortcut is available from any setup
screen that displays the two receiver selection options
next to each other, such as the LEVELS and STEPSIZE
screens. Once the value has been set on one receiver,
the same value can be copied to the other receiver with
a simple button push combination.
Hold the MENU/SEL button and press the DOWN arrow
to copy the value set on receiver 1 to receiver 2. Hold
MENU/SEL and press UP to copy the value set on
receiver 2 to receiver 1.
+05
00 00
LEVEL LEVEL
00
Hold MENU and
press UP arrow
NOTE: It does not matter which receiver is selected
(highlighted).