Digital Receiver
Rio Rancho, NM
5
IR (infrared) Port
Frequency and settings can be transferred to and from
the DSQD receiver via this port to an IR enabled trans-
mitter to simplify setup.
USB Port
For firmware updates and connection to Wireless De-
signer software.
Reset Button
For MCU recovery in the event of an interrupted firm-
ware update.
Headphone Volume Adjustment
Knob adjusts the headphone monitor.
Antenna Bias LEDs
Illuminated when antenna bias power is turned on.
Channel Selector Buttons
From the main screen, pressing a
Channel Selector
Button
will show a detailed channel screen (see
Quick
Start
for more information).
NOTE: Press and holding channel selector buttons
will initiate a sync with a transmitter from most
screens.
Antenna Loop-thru
For multiple DSQD installations in a rack, a “loop-thru”
is available to feed two or three receivers from a single
antenna pair. Connect coaxial cables from the multicou-
pler loop-thru outputs on the first receiver to the anten-
na inputs on the next receiver in the stack.
WARNING: Do not enable antenna power if
connecting antenna loop-thru outputs on one
receiver to the antenna inputs on another
receiver.
Dante Ports (if Dante module is installed)
Connects to a Dante digital audio network.
AES3 Ports (DSQD/AES3 option)
AES3 outputs on two TA3M jacks (in place of the two
Dante ports shown)
Ethernet Port
Used for setup, monitoring and control with Wireless
Designer software or 3rd party control systems con-
nected via a network.
Multi-Frame Communication
Allows offline, multi-frame communication and frequen-
cy coordination (coming soon).
Power Inlet
The locking DC coaxial inlet requires 7-18 VDC and
draws a maximum of 2.5 A at 7 V (with all channels
powered, Dante module powered, and antenna bias
power on both channels).
Operating Instructions
To begin using the DSQD quickly, follow the steps be-
low. The other settings can be adjusted as needed.
1. Set Channel Frequency:
Assign a frequency to
each channel, which will correlate to the accom-
panying
Channel Selector Button
(1-4). From
the
Quick Access Menu
or the
RF Setup Menu
,
manually set frequency on the
RF Frequency
screen or scan for available frequencies and assign
a frequency to each channel from the
Frequency
Scan
screen.
2. Set Compatibility Mode:
From the
Quick Access
Menu
or the
Audio Setup Menu
, set compatibility
modes for each channel.
3. Set Encryption Keys:
From the
IR Sync & En-
cryption Menu
, select a key type and then create a
key (if needed).
NOTE: See
Encryption Key Management
for
more instruction.
4. Sync Settings:
From the
Quick Access Menu
or
the
IR Sync & Encryption Menu
, initiate sync for
each channel via the IR port. Hold the target trans-
mitter close to the IR port on the front panel of the
DSQD. Select
SEND ALL
. A message will appear
on the main screen letting you know the sync was
successful. Messages will appear letting you know
if the sync was successful.
NOTE: See
Sync Settings
for more instruction.
5.
You can also quickly check a channel’s status by
pressing a
Channel Selector Button
from the
DSQD home screen. This screen allows you to
change a variety of settings, including status of the
compatibility mode, diversity setting, transmitter bat-
tery status, audio level and audio mute status.
Carrier
frequency
Compatibility
Mode
Audio
Level
Channel Selector
Buttons
Transmitter
Battery Status
Group Tune
On/Off
Mute
On/Off
Diversity
Setting
RF Level
with 10 seconds
of history
Содержание D-Squared DSQD
Страница 22: ...DSQD Manual LECTROSONICS INC 22...
Страница 23: ...Digital Receiver Rio Rancho NM 23...