Lectrosonics D-Squared DSQD Скачать руководство пользователя страница 14

Страница: 14 / 24

DSQD Manual

LECTROSONICS, INC.

TX Battery Timer Alert

Set transmitter battery timer alerts for each channel.

Choose to enable/disable alert, set time in hour and

minutes and reset timer. Use

MENU/SEL

to set and

move the cursor and the

and

DOWN

arrows to

change values.

Front Panel Setup

Front panel settings may be customized as follows:

• LCD brightness: Use

and

DOWN

arrows to

choose from 100%, 75%, 50% or 25%

• LCD Timeout: Use

and

DOWN

arrows to

choose from Always On, 30 seconds, or 5 minutes

• Front Panel Lock: Use

and

DOWN

arrows to

turn lock on/off. When locked, menus can still be

viewed, settings can not be changed. When locked,

if the

and

DOWN

arrows are pressed to change

settings, a “FRONT PANEL LOCKED” message will

appear.

Dante Power Enable

Enable or disable Dante as needed.

Antenna Bias Power

DC bias voltage can be supplied on the antenna input

BNCs from an internal source to power remote RF

amplifiers.

NOTE: See Panels and Features for more

information on antennas/connectors.

Network Settings

Allows the user to set network settings when needed.

The following controls are available:

• DHCP Enable - this is checked if DHCP is used to

assign an IP address, Netmask and Default Gate-

way to the device. Uncheck this to use “static” IP

addressing.

• IP Address - This is in “dotted quad” format. If

DHCP is enabled, this is read only.

• Netmask - This is in “dotted quad” format. If DHCP

is enabled, this is read only.

• Default Gateway - This is in “dotted quad” format. If

DHCP is enabled, this is read only.

• TCP Port - This is the Primary TCP port number, an

integer in the range 0 - 65535. The Secondary TCP

port number is not set directly - it is always the next

number after the Primary TCP port number. The

defaults are 4080 for the Primary port and 4081 for

the Secondary port.

• MAC Address - this is the address of the device

ethernet port, assigned at the factory. It is read only.

IMPORTANT: Always consult your network

administrator before attempting to connect and

configure a processor for a network interface.

NOTE: New network settings require the unit

to reboot to take effect. Making a change and

pressing the BACK key will prompt the user to

Reboot Now, Save and Exit, or Discard and Exit.

IMPORTANT: The CAT 5 Ethernet Cable must

be installed prior to powering up the DSQD.

Edit Names

Edit channel names to easily identify talent or easily

identify multiple DSQD receivers in a rack (1 name per

frame). Use

and

DOWN

Arrows to select letters and

bottom buttons to set and move cursor. Press

MENU/

SEL

when finished to save.

Содержание D-Squared DSQD

























Результаты поиска

Содержание D-Squared DSQD

Отзывы:

Lectrosonics D-Squared DSQD, Руководство пользователя, Страница: 14 / 24

Результаты поиска

Содержание D-Squared DSQD

Отзывы: