Lectronics Venue 2-941 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 32

Lectronics Venue 2-941 Скачать руководство пользователя страница 17

Digital Hybrid Wireless

®

Modular Receiver System

Rio Rancho, NM, USA

17

Firmware Update

Firmware updates are detailed in the Wireless De-

signer software help file. Launch the software and click

on Online Help, then on Venue2 Receiver Setup and

Monitoring, then on the item for updating firmware.

System Restore

If a firmware update fails, the receiver will need to

be restored with the following procedure. Review the

Firmware Update Procedure in the online help before

proceeding.

1) Remove power from the VRM2 - you have to

actually remove the DC power cable on the rear

panel of the unit.

2) Using a paper clip, or similar object, depress the

small, white, unmarked button recessed into the

front panel to the left of the headphone jack. This

is the Recovery Mode button.

Recovery Mode button

3) While keeping the Recovery Mode button de-

pressed, plug in the DC power jack to the rear of

the unit. The LCD will light up but be blank.

4) The unit will now be in the “Recovery Mode.” Re-

lease the Recovery Mode button.

5) Open Wireless Designer, and proceed to update

the firmware using the normal steps, EXCEPT

be sure to click and mark the “Recovery Mode”

check box at the bottom of the screen.

Recovery Mode check box

NOTE: The sample image above shows the DR

receiver front panel, with a different location of

the Recovery Mode button

6) Follow the on-screen instructions. If the firmware

update is successful, an on-screen message will

appear as confirmation.

When the process is complete, turn the receiver

off and then back on again to verify that the unit

is operational.

«
...
15
16
17
18
19
...
»

Содержание Venue 2-941

































Отзывы:

Нет отзывов