LeCroy USB Mobile HS Скачать руководство пользователя страница 117

Страница: 117 / 154

USB

MobileHS

User Manual

Chapter 10: Recording Options

LeCroy Corporation

109

10.2 Recording Speed

The

Misc

tab settings allow you to set the speed of traffic and to configure the Analyzer

to record On-The-Go traffic.

•

On the Go

: Check this if you are tracing an On the Go device. This allows

session request protocol detection.

•

Dual Role Devices

•

2DRD

: If both devices are Dual-Role devices, check this box to enable

Host Negotiation Protocol (HNP) detection.

•

A Dev Name

: Enter a name of your choice to refer to the device that

receives the mini-

plug.

•

B Dev Name

: Enter a name for the device that receives the mini-

plug.

•

Assume B is 1st Host

: Check this box if your scenario is one where the B

device is acting as host when the trace is started. If the trace incorrectly
identifies the wrong host, you can change it when viewing it by clicking on the
host field of a packet and selecting a switch to the other host ID.

Содержание USB Mobile HS



























































































































































Результаты поиска

Содержание USB Mobile HS

Отзывы:

Похожие инструкции для USB Mobile HS

Бренды по названию

Популярные бренды

LeCroy USB Mobile HS, Руководство пользователя

Результаты поиска

Содержание USB Mobile HS

Отзывы:

Похожие инструкции для USB Mobile HS

Бренды по названию

Популярные бренды