background image

 

Warranty 

LeCroy warrants this oscilloscope accessory for normal use and operation within specification for a period of one 
year from the date of shipment. Spare parts, replacement parts and repairs are warranted for 90 days. 

In exercising its warranty, LeCroy, at its option, will either repair or replace any assembly returned within the 
warranty period to the Customer Service Department of an authorized service center. However, this will be done 
only if the product is determined by LeCroy’s examination to be defective because of workmanship or materials, 
and the defect is not caused by misuse, neglect, accident, abnormal conditions of operation; or, damaged by 
attempted repair or modifications by a non-authorized service facility. 

The customer will be responsible for the transportation and insurance charges for the return of products to the 
service facility. LeCroy will return all products under warranty with transportation charges prepaid. 

This warranty replaces all other warranties, expressed or implied, including, but not limited to, any implied warranty 
of merchantability, fitness, or adequacy for any particular purposes or use. LeCroy shall not be liable for any 
special, incidental, or consequential damages, whether in contract or otherwise. 

Corporate Headquarters 

700 Chestnut Ridge Road 
Chestnut Ridge, NY 10977-6499 
Tel: (845) 425-2000  Fax: (845) 425-8967 

Internet:

 www.lecroy.com 

© 2006 by LeCroy Corp. All rights reserved. 

LeCroy, ActiveDSO, ProBus, SMART Trigger, JitterTrack, WavePro, WaveMaster, WaveSurfer, and Waverunner 
are registered trademarks of LeCroy Corporation. Other product or brand names are trademarks or requested 
trademarks of their respective holders. Information in this publication supersedes all earlier versions. Specifications 
subject to change without notice. 

Manufactured under an ISO 9000 
Registered Quality Management 
System 
Visit www.lecroy.com to view the 
certificate.

 

 

This electronic product is subject 
to disposal and recycling 
regulations that vary by country 
and region. Many countries 
prohibit the disposal of waste 
electronic equipment in standard 
waste receptacles. 

For more information about proper 
disposal and recycling of your 
LeCroy product, please visit 
www.lecroy.com/recycle. 

PP011-OM-E Rev A 

914602-00 Rev A 

 

PP011-OM-E Rev A 

Содержание PP011













Отзывы: