background image

 WaveSurfer Accessory

„

 Safety Requirements 

This section contains information and cautions that must be 
observed to keep the External USB Printer operating in a correct 
and safe condition. You are required to follow generally accepted 
safety procedures in addition to the safety precautions specified in 
this section. 

 

Safety Symbols 

The following symbols may appear on the product and they alert 
you to important safety considerations. 

 

 

This symbol is used where caution is required. Refer to the   
accompanying information or documents in order to protect   
against personal injury or damage to the instrument. 

 
 
 

              The CAUTION sign indicates a potential hazard. It calls   
       attention to a procedure, practice or condition which,  
       if not followed, could possibly cause damage to equipment.   
              If a CAUTION is indicated, do not proceed until its   

CAUTION 

       conditions are fully understood and met. 
 
Before using this product, ensure that its operating environment will 
be maintained within these parameters: 

Temperature:

 

0 to 40 

o

C  

Humidity:

   

30%RH to 80%RH    (non-condensing) 

 

 

 

 

1

 

Содержание GP-EXT
































Отзывы: