l'eau miracle water MW-30 Скачать руководство пользователя страница 5

Страница: 5 / 30

Miracle Water Installation & Operation Manual

Product Specifications

This model is efficiency rated. The efficiency rating is valid only at the minimum salt dose. This

softener has a demand initiated regeneration (D.I.R.) feature that complies with specific perform-

ance specifications intended to minimize the amount of regenerant brine and water used in its

operation.
This softener has a rated softener efficiency of not less than 3,350 grains of total hardness

exchange per pound of salt (based on sodium chloride) and shall not deliver more salt than its

listed rating or be operated at a sustained maximum service flow rate greater than its listed rat-

ing. This softener has been proven to deliver soft water for at least ten continuous minutes at

the rated service flow rate. The rated salt efficiency is measured by laboratory tests described in

NSF/ANSI Standard 44. These tests represent the maximum possible efficiency that the system

can achieve. Operational efficiency is the actual efficiency after the system has been installed.

It is typically less than the rated efficiency, due to individual application factors including water

hardness, water usage, and other contaminants that reduce a softener's capacity.

MW-30

Rated Service Flow Rate (gpm)

8.0

Amount of High Capacity Ion Exchange Resin (cu. ft.)

.82

Pressure Drop at Rated Service Flow (psig)

9.3

Water Supply Max. Hardness (gpg)

Water Supply Max. Clear Water Iron (ppm)

Water Pressure Limits (min./max. psi)

20 - 100

Min. - Max. Water Temperature (°F)

40 - 120

Min. Water Supply Flow Rate (gpm)

Max. Drain Flow Rate (gpm)

2.0

Performance Claims

MW-30

14,700 @ 2.9

Rated Softening Capacity (Grains @ Pound Salt Dose)

25,400 @ 8.0

30,100 @ 13.1

Rated Efficiency (Grains/Pound of Salt @ Minimum Salt Dose)

5,060 @ 2.9 lbs.

Water Used During Regeneration @ Minimum Salt Dose

2.3 gal. / 1,000 grains

Total Water Used Per Regeneration @ Maximum Salt Dose

35.2 gallons

This system conforms to NSF/ANSI 44 for the specific performance claims as verified

and substantiated by test data.

Miscellaneous Service Information

DESIGN SPECIFICATION

MW-30

FILL CYCLE

FLOW

.3 gpm

BRINE CYCLE

FLOW

.22 gpm

BRINE RINSE CYCLE

FLOW

.15 gpm

BACKWASH CYCLE (MAX.)

FLOW

2.0 gpm

FAST RINSE CYCLE (MAX.)

FLOW

2.0 gpm

gallon per minute flow to brine tank

gallon per minute flow to drain

Содержание MW-30































Результаты поиска

Содержание MW-30

Отзывы:

Похожие инструкции для MW-30

Бренды по названию

Популярные бренды

l'eau miracle water MW-30, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MW-30

Отзывы:

Похожие инструкции для MW-30

Бренды по названию

Популярные бренды