l'eau miracle water MW-30 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 30

background image

10

Miracle Water Installation & Operation Manual

Other Requirements

• A 120V-60Hz, grounded electrical outlet (continuously ‘‘live’’) is needed nearby the unit.
• A drain is needed for regeneration discharge water. A floor drain, close to the unit, is preferred.

A laundry tub, standpipe, etc., are other drain options.

Tools and Materials You May Need

• Common Screwdriver

• Tape Measure

•Pliers

• Pipe and fittings as required

Soldered Copper

• Tubing cutter

• LEAD-FREE solder and flux

• Propane torch

•Emery cloth, sandpaper or steel wool

• Misc. fittings

Threaded

• Pipe cutter or hacksaw

• Pipe joint compound

• Threading tool

• Misc. fittings

CPVC Plastic

• Pipe cutter

• Solvent cement

• Hacksaw

• Primer

• Adjustable wrench

• Misc. fittings

NOTE: The salt storage tank drain elbow accepts either 1/2” or 3/8” I. D. hose.

«
...
8
9
10
11
12
...
»

Содержание MW-30































Отзывы:

Нет отзывов

Похожие инструкции для MW-30

Solar Storage Tank Water Heater

Бренд: American Water Heater Страницы: 15

Бренд: Oasis Страницы: 10

Бренд: Altech Страницы: 47

GNCF04H/GXCF05D

Бренд: GE Страницы: 28

Бренд: Soleus Air Страницы: 5

Бренд: STIEBEL ELTRON Страницы: 16

Бренд: Siemens Страницы: 8

Бренд: Siemens Страницы: 16

Бренд: Siemens Страницы: 34

Бренд: Siemens Страницы: 36

Бренд: Siemens Страницы: 24

Бренд: Siemens Страницы: 32

Бренд: Siemens Страницы: 32

Бренд: Siemens Страницы: 36

Бренд: Siemens Страницы: 56

Бренд: Accucold Страницы: 23

Бренд: Ariston Страницы: 16

Бренд: Ariston Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды