background image

Leaf LTHDMI88 / LTHDMI88E manual 

 

Page  9 

Of  16 

 

3.4  IP port 

The RJ45 type IP port is a dedicated port for controlling the LTHDMI88/E. This may not 
be  active  on  all  versions  of  LTHDMI88  /  LTHDMI88E.  Further  information  and 
specifications can be found in supplementary documentation available on request from 
Leaf.

 

3.5  RJ12 control port 

The  6 wire RJ12 port enables the LTHDMI88/E to be controlled by a proprietary LEAF 
controller such as the TC3.  

3.6  4 way DIP switch module 

The  rear  panel  accessible  4  position  DIP  switch  controls  functionality  of  the 
LTHDMI88/E. The table below summarizes the settings: 

NOTE: The interface will only read the DIP switch settings on power-up. The unit must 
be powered off and then back on again for it to respond to any change of the DIP 
switch settings.  

 

DIP SWITCH 

OFF (down) 

ON (up) 

Global IR direction IN 

IR RX detectors at LTB1/E 

breakouts 

 IR TX blasters at 

LTHDMI88/E 

Global IR direction OUT 

IR RX detectors or devices at  

 LTHDMI88/E 

IR TX blasters at LTB1/E 

breakouts

 

IR Input device type  

(Applies when DIP 1 =ON) 

IR RX detectors (eg Leaf 

Hammerhead) at  

 LTHDMI88/E 

IR Input device type  

(Applies when DIP 1 =ON) 

IR direct drive from control 

system (5 volt only) at 

LTHDMI88/E 

Future Function 

Future Function  

Future Function 

Future Function 

 

Table 2: Dip Switch Settings 

3.7  Audio ports 

The Stereo Analog and S/PDIF RCA connectors are configured as zone based audio 
outputs for connection to local external amplifiers. These provide audio output from the 
particular source that is switched to the connected zone at that time.  

 

Note: The Aud

io Channel Return (ARC) from the zones’ breakout is not currently able 

to be routed to these outputs. 

3.8  3.5mm IR ports  

The  3.5mm  Remote  IR  connectors  are  used  for  routing  the  control  signals  in  one 
direction  between  the  LTHDMI88  /  LTHDMI88E  and  the  connected  LTB1  /  LTB1E 
breakouts.  (See  table  2  for  DIP  switch  configuration  details.)  These  connections  are 
treated  as  through  connections.  That  is,  IR  port  1  connects  to  the  breakout  on 
HDBaseT 1 connection  through to port 8 being connected to HDBaseT 8.  

Содержание LTHDMI88

















Отзывы: