Leadshine DM805-AI Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 30

background image

iii

HWMN-DMAI-R20110627

Safety Items

!

Notice

Read this manual carefully before trying to install the stepper drive into your system. The person
setup the stepper drive should have a better understanding on electronics and mechanics. Contact
Leadshine technical guys when have questions on this document.

!

Caution

Make sure the power supply voltage dose not exceed the drive’s input range. Double check the
connections and make sure the power lead polarity is correct.

!

Warning

Do not set high current to small stepper motor. It is possible that the motor will be damaged.

!

Caution

Disconnect the motor from the load if you are not sure the move direction. Adjust the axis in the
middle before trying to run the motor.

!

Warning

Never disconnect the motor lead when the power source is energized.

«
1
2
3
4
5
...
»

Содержание DM805-AI































Отзывы:

Нет отзывов

Похожие инструкции для DM805-AI

Бренд: ABB Страницы: 2

Бренд: QUAD Страницы: 17

Бренд: fadini Страницы: 16

Бренд: nekos Страницы: 8

Бренд: nekos Страницы: 8

Бренд: Neles Страницы: 12

Бренд: Parker Страницы: 32

Бренд: Rayrun Страницы: 4

AeGIS 7000 Series

Бренд: PACH & COMPANY Страницы: 2

Бренд: Rain Bird Страницы: 4

Бренд: Rain Bird Страницы: 2

Бренд: Rain Bird Страницы: 140

WeatherSmart RSC600i

Бренд: Raindrip Страницы: 36

SYSMAC C500-NC222-E

Бренд: Omron Страницы: 164

Бренд: Tech 21 Страницы: 2

Бренд: Samson Страницы: 102

SUPERSTAR E-3000/F2

Бренд: praher Страницы: 10

Бренд: IDEC Страницы: 97

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды