Leadshine Technology MA860C Скачать руководство пользователя страница 13

                                      MA860C Full Digital Stepper Drive Manual V1.0

 

 

 

9 Frequently Asked Questions 

In the event that your drive doesn’t operate properly, the first step is to identify whether the problem is electrical or 
mechanical in nature. The next step is to isolate the system component that is causing the problem. As part of this 
process you may have to disconnect the individual components that make up your system and verify that they operate 
independently. It is important to document each step in the troubleshooting process. You may need this documentation 
to refer back to at a later date, and these details will greatly assist our Technical Support staff in determining the 
problem should you need assistance. 

Many of the problems that affect motion control systems can be traced to electrical noise, controller software errors, or 
mistake in wiring. 

9.1 Problem Symptoms and Possible Causes 

Symptoms 

Possible Problems 

Motor is not rotating 

No power 

Microstep resolution setting is wrong 

DIP switch current setting is wrong   

Fault condition exists 

The drive is disabled 

Motor rotates in the wrong direction   

Motor phases may be connected in reverse 

The drive in fault 

DIP switch current setting is wrong 

Something wrong with motor coil 

Erratic motor motion 

Control signal is too weak 

Control signal is interfered 

Wrong motor connection 

Something wrong with motor coil 

Current setting is too small, losing steps 

Motor stalls during acceleration 

Current setting is too small 

Motor is undersized for the application   

Acceleration is set too high 

Power supply voltage too low 

Excessive motor and drive heating 

Inadequate heat sinking / cooling 

Automatic current reduction function not being utilized 

Current is set too high 

 
 
 
 
 
 

 

 

 

Содержание MA860C
















Отзывы: