©MMXI - LEADER LIGHT – All right reserved
Edition: A - 2012
Additional information on [email protected]
Page 2 /2
03.4 Control data connection
Control data cable length is specifi ed by Norm IEC929 Annex E4.
It is necessary to open the Driver box before connecting of DMX512 control
signal. Interconnections are realized by... connectors.
Pin connections:
Pin 1 – ground
Pin 2 – signal negative
Pin 3 – signal positive
-
-
-
03.5 DMX channels - only for DIM VERSION!!!
These informations are subject to change, latest data are on: www.leaderlight.eu
Order
code
Product name
LL47 305.426* LL SPORT D630-NA-I20 SW; 5.600K
LL47 315.426* LL SPORT D630-NA-I20 DIM; 5.600K
04 MAINTENANCE AND SERVICE
Before any maintenance is necessary to carefully read all
SAFETY INFORMATION 01!
Damages caused by inadequate cleaning or maintenance are not covered by warranty.
Requires periodic cleaning (dust, dirt ,...)
Procedure for maintenance:
Unplug mains before maintenance and at least 10 minutes cool off.
Appliance do not illegal open or demount.
-
-
-
-
-
!
Functions Dip1-Dip4:
ModA:
Dip3=Off, Dip4=Off (1ch, 8b+fade)
1ch: all White
Adress:
Dip1=Off, Dip2=Off : DmxAdress=1
Dip1=On, Dip2=Off : DmxAdress=2
Dip1=Off, Dip2=On : DmxAdress=3
Dip1=On, Dip2=On : DmxAdress=4
ModB:
Dip3=Off, Dip4=On (6ch, 8b+fade)
1ch: White1
2ch: White2
3ch: White3
4ch: White4
5ch: White5
6ch: White6
Adress:
Dip1=Off, Dip2=Off : DmxAdress=1
Dip1=On, Dip2=Off : DmxAdress=7
Dip1=Off, Dip2=On : DmxAdress=13
Dip1=On, Dip2=On : DmxAdress=19
ModC:
Dip3=On, Dip4=Off (2ch, 16b)
1ch: all White High
2ch: all White Low
Adress:
Dip1=Off, Dip2=Off : DmxAdress=1
Dip1=On, Dip2=Off : DmxAdress=3
Dip1=Off, Dip2=On : DmxAdress=5
Dip1=On, Dip2=On : DmxAdress=7
ModD:
Dip3=On, Dip4=On (AutoTest)
Overlapping six channels.
* Order code: LL47 ---.xyz:
"x" = Product colour: x = 1 (RAL 9005), x = 4 (RAL 9006) ,
"y" = IP: y = 2 (IP20), y = 4 (IP43), y = 6 (IP67),
"z" = Light colour temperature: z = 1 (3.000K), z = 2 (3.500K), z = 3 (4.000K), z = 4 (4.500K), z = 5 (5.000K), z = 6
(5.500K), z = 7 (6.000K) +/- 200K
3. Fixture fi xation
3.1 Variable angle setup 0°-75°.
The standard bracket offers two options for fi xture fi xation: variable angle setup or step setup:
3.2 Step setup 0°-15°-30°-45°-60°-75°.
2. Mechanical mounting of LL SPORT D630-NA-I20
AIMING POSSIBILITY
The whole fi xture could be aim
to wish position with adjustable
bracket.
Mounting on surface:
2.1 Screw the fi xture to the surface (3xM10)
1. Power and DMX (only DIM version) connecion
1.1. Before connecting the power and DMX (DIM
version) remove the cover from the Driver box!
Rotary DIP (DIM version) set before the physical
installation!
N
L
+
_
+
_
N
L
Shut down power before installation or maintenance.
Do not modify, alter, or attempt to service the LEADER LIGHT appliance. Doing so will void the warranty.
Appliance and recommended AC power supply must be installed by a qualifi ed professional in accordance with relevant local codes. Use only acceptable source of AC power and frequency that complies with local
biulding and electrical codes.
Use only the recommended voltage source.
Appliance always connect to earth (eltech.)!
Do not use or do not connect the products if the power cable, power plug or fi xtures are any way damaged, wet, or if they are overheating.
Before removing or installing any cover or part of appliance disconnect it from AC power.
AC power supply must be protected against overvoltage and short circuits.
-
-
-
-
-
-
-
-
!
100-260V
AC
50-60Hz
DMX
IN/OUT
DIP
Clean-up dust only from outer surface. Use vacuum or dumpy duster (warm water)
Before reinstalling make sure everything is intact and dry– no wet parts!
Service:
Customer service provided by the manufacturer.
-
-
-
cable slot
slot for cable fi xation
1.2. Connect the power and DMX (DIM version).
1.3. After DIP setup, connecting the DMX (DIM version)
and power, you
must mount back the DRIVER cover!
90V
~
264V
IP20
PENDING
