LBC LRP Скачать руководство пользователя страница 27

Страница: 27 / 32

Page | 27 Proofer Operators Manual 1-2022 (English)

Proofer control

Function settings Code 0008

Function Short Name

Description

Factory

set point

Range

Heat timer alarm

Sounds the alarm if the set temperature is not reached
within the indicated number of minutes.

0 - 99

Temperature Calibration

Changes the displayed temperature in Degrees F to
match that of a calibration thermometer.

+25, -25

Humidity Calibration

Changes the displayed relative humidity to match that
of a calibration meter.

+25, -25

Temperature Lock

Limits the range of temperature variance shown in
degrees.

0 - 99

Humidity Display Limit

Limits the range of displayed humidity from the set
point. 00 turns this function off.

0 - 99

Proofer control

Function settings Code 0088

Proportion Factor

Sets the ratio of proportional on time to temperature
difference.

Heat cycle time

Sets the length of the PID cycle in seconds.

Temperature Cycle Rate

This controls how often the temperature proportional
output will turn on.

Humidity Cycle time

Sets the length of time in seconds for each humidity
cycle.

16 - 32

Humidity On time

Sets the "on" time in seconds for humidity in each
cycle.

0 - 20

Upper Humidity Alarm

This sets the alarm range for humidity overshoot. It
should be set to 00 to turn it off.

0 - 99

N/A

This function is inactive.

N/A

Inactive

Alarm Off/On

Turns alarm output on or off.

00 - 01

Max Set Temp

Limits the maximum temperature the operator can set.

105

00 -

01.22

Open Door Shut-off

Sets how long the door can be open before the proofer
turns off. Set to 00 to disable.

0.0 - 99

Unattended Humidity
Shut-off

Sets how long the proofer can be left unattended (Door
Closed) before the humidity turns off.

0.0 - 99

Содержание LRP




























Результаты поиска

Содержание LRP

Отзывы:

Похожие инструкции для LRP

Бренды по названию

Популярные бренды

LBC LRP, Руководство оператора

Результаты поиска

Содержание LRP

Отзывы:

Похожие инструкции для LRP

Бренды по названию

Популярные бренды