LBC LMO-E-P Скачать руководство пользователя страница 6

Страница: 6 / 34

–

2022 LBC BAKERY EQUIPMENT, INC. 6 REV 6-2022B

CONDITIONS of INSTALLATION (Part 2 of 2)

)

The LMO oven ships with the following items please inspect your shipment to ensure that these
items were included.

•

LMO Oven Rack

•

Decorative hood front, sides and back pieces

If moving the oven through a 36” door opening it will be necessary to remove the oven door, door

latch, door hinges decorative valance and the rear panel.

Location

This appliance is

not intended for outdoor use

. This appliance is

not intended for residential use

This appliance is intended for commercial use in locations suitable for use as listed in this manual.

Clearances to combustible and non-

combustible construction: 0” from back, sides and top.

This appliance is suitable for installation on combustible floors.

Installation Codes

For US Installation:

The LMO oven must be installed in accordance with all State and local codes as

well as the National Electrical Code, ANSI/NFPA-70 (latest edition). Gas ovens must be installed in
accordance with the National Fuel Gas Code, ANSI-Z223-1/NFPA 54 (latest edition).

For Canadian installation:

The LMO oven must be installed in accordance with all local codes. Gas

ovens must be installed in accordance with the CAN/CGA-B149.1 National Gas Installation Code

Gas Ovens:

The appliance and its individual shutoff valve must be disconnected form the gas supply

piping system during any pressure testing of that system at pressures in excess of ½ psi.

Gas Ovens:

The appliance must be isolated from gas supply piping system by closing its individual

manual shutoff valve during any pressure testing of the gas supply piping system at test pressures
equal to or less than ½ psi.

Model Number Coding

Electric Oven Number Format: LMO

EX-Y-Z,

where

= rack size (use

for 6-pan rack,

for 8-pan

rack),

= voltage (use -

208

for 208V,

-240

for 240V and

-480

for 480V)

and

= base (use

-S

for stand,

for proofer base). Example: LMO-E8-480-P is a 480V electric oven with an 8-pan rack and proofer

base.

Gas Oven Number Format: LMO

GX-Y-Z

, where

= rack size (use

for 6-pan rack,

for 8-pan rack),

= gas type (use -

for natural gas, -

for propane gas)

and

denotes the base (use

-S

for stand, -

for proofer base). Example: LMO-G6-N-S is a natural gas oven with a 6-pan rack and stand.

Содержание LMO-E-P























Результаты поиска

Содержание LMO-E-P

Отзывы:

Бренды по названию

Популярные бренды

LBC LMO-E-P, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание LMO-E-P

Отзывы:

Бренды по названию

Популярные бренды