Making a call using a Headset
With a headset connected
Press the button
Enter the required number.
The call can be conducted via the headset.
Adjust the volume heard from the headset using the buttons.
To terminate the call,
press the button again
, the IN-USE light will go out and the phone will
drop the line.
An incoming call may be answered in the Headset mode by pressing the button.
The phone allows you to make or receive calls in a full Hands-free mode. The phone has a sensitive switch
that monitors who is speaking at any one time. It switches rapidly between you and your caller as you speak in
turn. If both parties try to speak at the same time, parts of the conversation may be cut off. This is normal.
It is recommended that the Hands-free mode is used in a quiet environment. High levels of background noise
may cause the intermittent loss of speech.
When using Hands-free, the phone should be positioned such that your mouth is around 2 to 3 feet from the
telephone. Distances greater than this may result in inferior performance and the likelihood of background
noise causing the loss of speech is increased.
Making a call using Hands-free
With the phone in the IDLE mode
Press the button.
Enter the required number.
Adjust the volume heard from the speaker using the buttons.
To terminate the call,
press the button
again, the IN-USE light will go out and the phone will
drop the line.
An incoming call may be answered in the Handsfree mode by pressing the button.
To switch from Handsfree to handset.
Whilst making a call using the Speakerphone
Pick up the handset
. The handsfree mode will be terminated and the call can continue on the handset.
To switch from handset to Handsfree.
Whilst making a call using the handset
Press the button and return the handset to the cradle
. The call can continue in the
handsfree mode
Speakerphone Volume
The volume of the incoming caller, heard through the speaker, can be adjusted using the
buttons.
Headset Operation
Speakerphone (Handsfree)
A headset may be connected to the socket provided on the
left side of the phone. The phone will detect that a headset is
connected and switch Speakerphone (Handsfree) functions
to the headset.
Headset socket
Wall Mounting
Handset clip -
In order to hold the handset in place when wall mounted, there is a reversible clip located
beneath the hookswitch. Slide the clip towards the hookswitch to remove it. Rotate it through 180 degrees and
slide it back into position.
There will now be a protruding lip onto which the handset will locate when hung vertically.
Fixing screws -
To attach the phone to the wall, 2 screws are used
The screws should be fixed to the wall, 85mm apart, in a vertical plane. The slots in the base of the phone will
then locate onto these screws. The screws should be adjusted so that the phone is held securely.
IMPORTANT NOTE : Before fitting the fixing screws to the wall, ensure that the wall is capable of supporting
the weight of the phone and that there are no pipes or wires hidden in the wall, behind the telephone position.
Do not attempt to wall mount the phone in a position where there is an electrical switch or socket either
vertically above or below the required position, unless you are sure the wiring to that fitting does not run behind
the proposed telephone location. Also ensure that the telephone line cord will reach to your telephone socket
from the proposed location.
Installation
Handset curly cord
Straight telephone
line cord
2 wire Data socket
1
4
Connect the cords
Plug one end of the curly cord into the socket in the handset
and the other end into the socket on the left side of the phone.
Note there are 2 sockets on the left side of the phone
(headset and handset). Ensure the handset curly cord is
plugged into the correct socket marked with the symbol.
The straight telephone line cord should be plugged into the
socket at the rear of the phone and into a suitable telephone
wall outlet.
Note - the straight (UK) line cord provided with this phone has
4 wires. The outer 2 wires of the UK wall plug connect to the
inner 2 connections of the phone (a crossover cable).
Please use only the cable supplied with the phone.
Data Socket
An additional RJ45 socket on the right side of the phone is
provided for the connection of a modem. This socket utilising
the centre 2 connections for the telephone 'A' and 'B' wires.
